Adaptec 3940UW User Guide - Page 66

Setting SCSI IDs, Installing Multiple PowerDomain 2940UW, 3940UW Accelerator Cards

Get Adaptec 3940UW - Storage Controller UW SCSI 40 MBps PDF manuals and user guides View all Adaptec 3940UW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

PowerDomain 2940UW/3940UW User's Guide Setting SCSI IDs Each device on the SCSI chain, including the accelerator card, must have a unique SCSI ID. The computer uses the SCSI ID to identify the SCSI device on the SCSI chain. Setting SCSI IDs is a two-step process: 1 Determine the SCSI ID of each device to be connected on the SCSI chain. The PowerDomain 2940UW/3940UW is shipped with a SCSI ID of 7. To determine the SCSI IDs of disk drives, CD-ROM drives, and other devices, refer to the device documentation. 2 Change the SCSI IDs, if needed, so no IDs are duplicated on the same SCSI chain and each device has an appropriate SCSI ID. Installing Multiple PowerDomain 2940UW/ 3940UW Accelerator Cards You can install multiple PowerDomain 2940UW/3940UW accelerator cards in your computer if enough PCI expansion card slots are available. Each accelerator card has its own separate SCSI chain and attached SCSI devices. To install additional accelerator cards, repeat steps 7 through 10, beginning on page 2-7. Note: If you encounter any problems during installation, see Chapter 4, Troubleshooting. ❒ 2-54 AAAAAAAAAAAAAAAAAPSPCAAAAAArotuoiAAAwrncAAArtekAAAeSrAAAnNDAAAptAAAeuoDAAAcmmAAAaAAANtbaeAAAieu:AAAnrmAAA2:2AAA/5bAAA921eAAA04r0AAA/0:AAA98U4AAA66AAA9W4AAA3-AAA0/7AAA304AAA9,2AAA4R-AAA00AAAeU0AAAvAAAW.AAABAAAAAAUAAAsAAAeAAArAAA'AAAsAAAEGAAACAAAuAAANiAAAdAAAeDAAAAAAaAAAPtAAAeaAAA:gAAA2AAAe/AAA:2AAA27AAA-/AAA59AAA46AAAAAAAAAAAAAAAAAAAA

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
2-54
PowerDomain 2940UW/3940UW User’s Guide
PowerDomain 2940UW/3940UW User’s Guide
Stock Number: 510864-00, Rev. B
Page: 2-54
Print Spec Number: 493742-00
Current Date: 2/20/96
ECN Date: 2/27/96
Setting SCSI IDs
Each device on the SCSI chain, including the accelerator card, must
have a unique
SCSI ID
. The computer uses the SCSI ID to identify
the SCSI device on the SCSI chain.
Setting SCSI IDs is a two-step process:
1
Determine the SCSI ID of each device to be connected on the
SCSI chain.
The PowerDomain 2940UW/3940UW is shipped with a SCSI
ID of 7. To determine the SCSI IDs of disk drives, CD-ROM
drives, and other devices, refer to the device documentation.
2
Change the SCSI IDs, if needed, so no IDs are duplicated on
the
same
SCSI chain and each device has an appropriate SCSI
ID.
Installing Multiple PowerDomain 2940UW/
3940UW Accelerator Cards
You can install multiple PowerDomain 2940UW/3940UW
accelerator cards in your computer if enough PCI expansion card
slots are available. Each accelerator card has its own separate SCSI
chain and attached SCSI devices.
To install additional accelerator cards, repeat steps 7 through 10,
beginning on page 2-7.
Note:
If you encounter any problems during installation,
see Chapter 4,
Troubleshooting
.