Alpine IDA X300 Owners Manual - Page 35
ch 3WAY System, 2ch FRONT/REAR/SUBW. System
UPC - 793276711489
View all Alpine IDA X300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 35 highlights
4 Repeat steps 1 to 3 to set another speaker. By setting these values to make its sound reach the listening position at the same time as the sound of other speakers. • You can select the next band by pressing and turning the Double Action encoder. • The User Preset screen can be recalled in the normal mode by pressing and holding PRESET for 2 seconds. Adjusting the Crossover Settings (X-OVER) Before performing the following procedures, refer to "About the Crossover" (page 36). 2.2ch (3WAY) System 1 After selecting X-OVER from the Sound Field Adjustment mode, turn the Double Action encoder to select the band adjustment, and then press /ENTER. 2.2ch (3WAY) System / NORMAL (L=R) Setting items: LOW / MID-L / MID-H / HIGH 2.2ch (3WAY) System / INDIVIDUAL (L/R) Setting items: LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L / MID-H-R / HIGH-L / HIGH-R 2 Turn the Double Action encoder to select an item to adjust, then press /ENTER. FC LV (cut-off (level) frequency) SLP (slope) FC (frequency) Cut-off frequency 3-1 Turn the Double Action encoder to select the desired cut-off frequency (Crossover Point). Adjustable frequency bands: 2.2ch (3WAY) System Setting items: LOW / MID-L 20 Hz~200 Hz MID-H HIGH 20 Hz~20 kHz (1 kHz~20 kHz)*1/(20 Hz~20 kHz)*2 *1 When Maker's is selected, refer to "Setting the Response Slope for the High Range Speaker (TW Setup)" (page 34). *2 When User's is selected, refer to"Setting the Response Slope for the High Range Speaker (TW Setup)" (page 34). Level Adjustment 3-2 Turn the Double Action encoder to adjust the output level. Adjustable output level: -12 to 0 dB. Slope Adjustment 3-3 Turn the Double Action encoder to adjust the slope. Adjustable slope: FLAT*, 6 dB/oct., 12 dB/oct., 18 dB/oct., 24 dB/oct. * FLAT can be set for the HIGH slope only when User's is selected in "Setting the Response Slope for the High Range Speaker (TW Setup)" (page 34). Depending on the response characteristics of the speaker, care should be taken when setting the response slope to FLAT, as speaker damage may result. With this unit, a message is displayed when the response slope for the high range speaker is set to FLAT. 4 Repeat steps 1 to 3 to make adjustment to the other bands. 4.2ch (FRONT/REAR/SUBW.) System 1 After selecting X-OVER from the Sound Field Adjustment mode, turn the Double Action encoder to select the band adjustment, and then press /ENTER. 4.2ch (FRONT/REAR/SUBW.) System / NORMAL (L=R) setting items: LOW (SUB-W) / MID (REAR) / HIGH (FRONT) 4.2ch (FRONT/REAR/SUBW.) System / INDIVIDUAL (L/R) setting items: LOW (SUB-W)-L / LOW (SUB-W)-R / MID (REAR)-L / MID (REAR)-R / HIGH (FRONT)-L / HIGH (FRONT)-R 2 Turn the Double Action encoder to select an item to adjust, then press /ENTER. FC LV (cut-off (level) frequency) SLP (slope) FC (frequency) Cut-off frequency 3-1 Turn the Double Action encoder to select the desired cut-off frequency (Crossover Point). Adjustable frequency bands: 4.2ch (FRONT/REAR/SUBW.) System Setting items: 20 Hz~200 Hz Level Adjustment 3-2 Turn the Double Action encoder to adjust the output level. Adjustable output level: -12 to 0 dB. Slope Adjustment 3-3 Turn the Double Action encoder to adjust the slope. Adjustable slope: FLAT, 6 dB/oct., 12 dB/oct., 18 dB/oct., 24 dB/oct. 4 Repeat steps 1 to 3 to make adjustment to the other bands. • You can select the next band by pressing and turning the Double Action encoder. • While adjusting the X-over, you should consider the frequency response of the connected speakers. • About the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system You can switch to 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system mode with the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) switch on the PXA-H100. For details, refer to the Owner's Manual of PXA-H100. • The User Preset screen can be recalled in the normal mode by pressing and holding PRESET for 2 seconds. 33-EN