Alpine PSS-20WRA Owners Manual
Alpine PSS-20WRA Manual
 |
View all Alpine PSS-20WRA manuals
Add to My Manuals
Save this manual to your list of manuals |
Alpine PSS-20WRA manual content summary:
- Alpine PSS-20WRA | Owners Manual - Page 1
so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as a result of failure to follow the instructions in the manuals. ˜ This manual includes a number of symbols that are intended to help you use the product safely, to prevent harm to you - Alpine PSS-20WRA | Owners Manual - Page 2
Types of Precautions UNLIMITED Jeep Wrangler ˜ 2/20 Forbidden Forbidden Indicates actions that are forbidden (must not be performed) Indicates that disassembly is forbidden. Mandatory Indicates actions that are mandatory (must be performed) Marks content that should receive your full attention - Alpine PSS-20WRA | Owners Manual - Page 3
or fire. Do not block vents or heat sinks. Doing so could lead to fire or damage equipment. Forbidden Use the accessories according to the instructions, and attach them securely. Failing to do so could lead to an accident or damage equipment. Forbidden Do not install the product where it may - Alpine PSS-20WRA | Owners Manual - Page 4
Tools Required Panel Removal Tool 9/32" Drill Bit Torx T15 T30 T45 Accessory List Parts List Subwoofer UNLIMITED Jeep Wrangler ˜ 4/20 Sockets 7mm 10mm 18mm Extension Power Drill #2 Phillips Screwdriver Ratchet Wire Cutters Amplifier Subwoofer Level Remote Amplifier Mounting Bracket R/L - Alpine PSS-20WRA | Owners Manual - Page 5
Accessory List Parts List (4) 8/32" Phillips Screws UNLIMITED Jeep Wrangler ˜ 5/20 (4) 12" X 12" Polyfill fiber sheets Main Wiring Harness SPT-70C Rear Component Speakers SPT-71C Front Component Speaker Hi/Lo RCA Adapter TWEETER SLIDE || OPEN INPUT TWEETER SLIDE || OPEN INPUT OEM T-Harness - Alpine PSS-20WRA | Owners Manual - Page 6
UNLIMITED Jeep Wrangler ˜ 6/20 Factory Unit Disassembly Process (2007-2010 Only) 1 Remove top panel by releasing (2) clips on the rear of the top panel and then pull panel forward. 2 Remove (2) 7mm screws from the top of the radio bezel. 3 Release (2) clips on the top of the bottom panel. This - Alpine PSS-20WRA | Owners Manual - Page 7
UNLIMITED Jeep Wrangler ˜ 7/20 Factory Radio Removal (2011 - 2014) 1 Remove the rubber cover from the top storage area and extract (1) 7mm screw. 2 Remove the knee cover panel and extract (2) 7mm screws located to the right and left sides of the steering wheel column. 3 Remove the window switch - Alpine PSS-20WRA | Owners Manual - Page 8
Passenger Seat Removal 1 Using an 18mm socket, extract the (4) seat bolts from the passenger side seat. UNLIMITED Jeep Wrangler ˜ 8/20 2 Using a T45 Torx extract (1) bolt from the seat belt anchor. Front view Confirm that the Battery has been disconnected before continuing to step 3. Rear view - Alpine PSS-20WRA | Owners Manual - Page 9
Top Dash Tweeter Removal 1 Remove top dash speaker grill using a panel removal tool. UNLIMITED Jeep Wrangler ˜ 9/20 2 Gently open the (3) lock tabs to release the factory tweeter. Front Speakers Removal 1 Using a Panel Removal Tool, remove the dash side covers by each door. 2 Remove the driver - Alpine PSS-20WRA | Owners Manual - Page 10
UNLIMITED Jeep Wrangler ˜ 10/20 Front Speakers Removal 5 Remove glove box by pushing both left and right sides inwards. 6 Extract (2) 7mm screws from the lower dash. '07-'11 Models have (4) screws. 7 Extract (2) 7mm screws from the side of each respective dash enclosure. '07-'11 Models have (2) - Alpine PSS-20WRA | Owners Manual - Page 11
UNLIMITED Jeep Wrangler ˜ 11/20 Sound Bar Speaker Removal 1 Remove (3) T15 Torx screws from the speaker grills. 2 Disconnect and remove the factory speaker. Tweeter Assembly 1 Connect the tweeter to the X-Over network. 2 Insert the SPT-10WRA tweeter into the factory tweeter grill. Insert the - Alpine PSS-20WRA | Owners Manual - Page 12
UNLIMITED Jeep Wrangler ˜ 12/20 Tweeter Installation 1 Connect the dash tweeters to the factory harness and mount X-Over network using a cable tie as shown below. 2 Push the X-Over through the tweeter opening and snap the tweeter into place. Front Speaker Installation NOTE: Polyfill installation - Alpine PSS-20WRA | Owners Manual - Page 13
UNLIMITED Jeep Wrangler ˜ 13/20 Subwoofer Installation (passenger side seat) 1 Position the seat in a secure manner to gain access to the bottom of the seat. 2 Using a T30 Torx, remove the OEM harness mounting plate as shown below. Use a panel removal tool to remove the two plugs from the - Alpine PSS-20WRA | Owners Manual - Page 14
Amplifier Installation 1 Use a 10mm socket to connect the power cable to the POSITIVE (+) battery terminal. Note: The NEGATIVE terminal should remain disconnected until the installation is completed. UNLIMITED Jeep Wrangler ˜ 14/20 2 Route the power cable following the OEM harness as shown below. - Alpine PSS-20WRA | Owners Manual - Page 15
UNLIMITED Jeep Wrangler ˜ 15/20 Amplifier Installation 7 Attach the anti-vibration foam to the amplifier, make all the necessary connections following the corresponding wiring diagram. See pages 16, 17 or 18. 8 Route the main harness along the center console as shown below. Rear of vehicle - Alpine PSS-20WRA | Owners Manual - Page 16
Exploded View UNLIMITED Jeep Wrangler ˜ 16/20 Passenger door side Center console side Bass Level Control Installation Mount the bass level control to an easily accessible location. We recommend mounting the control on the center console as shown below using the Velcro provided. - Alpine PSS-20WRA | Owners Manual - Page 17
Amp Turn-on Blue Amp Turn-On RED/WHITE L R RCA Adapter For a detailed Alpine Restyle headunit wiring diagram refer to it's corresponding installation manual. BLACK To Chassis Ground RED To Battery Cable MRV-F300 Amplifier Speaker Wiring CH 1 - White (+) White/Black (-) CH 2 - Gray(+) Gray/Black - Alpine PSS-20WRA | Owners Manual - Page 18
UNLIMITED Jeep Wrangler ˜ 18/20 PSS-20WRA Wiring Diagram Aftermarket Headunit To Vehicle Connectors Power/Speaker 16-pin Green Connector OEM T-HARNESS ADAPTER To 3rd party wire harness and radio replacement interface * Wire Harness and Interface sold separately Front Speakers 4 PIN WHITE - Alpine PSS-20WRA | Owners Manual - Page 19
UNLIMITED PSS-20WRA Wiring Diagram For Factory Headunit To Vehicle Connectors Power/Speaker 16-pin Green Connector To OEM Headunit OEM T-HARNESS ADAPTER Front Speakers 4 PIN WHITE CONNECTOR Rear 4 PIN BLACK CONNECTOR High Level Out Front Rear Subwoofer Front Rear Subwoofer Blue Amp Turn- - Alpine PSS-20WRA | Owners Manual - Page 20
UNLIMITED Jeep Wrangler ˜ 20/20 Troubleshooting Guide Symptom 1 System will not turn on 2 Volume is , loose pins, disconnected terminals etc.. Disconnect the battery and re-connect after 5 minutes. If problem is not solved, the vehicle will have to be taken to a Jeep dealer. Connect the Remote
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
Jeep Wrangler
UNLIMITED
±
1/20
Jeep Wrangler
PSS-20WRA Sound System
Installation Manual
±
Model: Wrangler Unlimited
±
Model Year: 2007 – 2014
*Not compatible with factory amplified systems
Introduction
±
Congratulations on purchasing the PSS-20WRA. This installation manual is designed to take you through the
step-by-step installation of the PSS-20WRA into a 2007 - 2014 Jeep Wrangler Unlimited. Please familiarize
yourself with the owners manual and if you still have additional questions please call 1-800-TECH-101.
Note
±
Design and specifications are subject to change without notice for improvement.
To Ensure Safe Use, Always Follow These Precautions
±
The installation of this product requires specialized skills and experience. We recommend that you have the
product installed by an Alpine authorized dealer.
±
Before you use this product, be sure to carefully read this installation manual and the separate user's manual
so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as
a result of failure to follow the instructions in the manuals.
±
This manual includes a number of symbols that are intended to help you use the product safely, to prevent
harm to you and others, and to protect against damage to property. These symbols and their meanings are
listed below. Make sure you fully understand these symbols before you begin reading the main text.
Explanations of Injury and Damage That May Result from Incorrect Use
Warning
Ignoring the content marked by this indication and using the product incorrectly may
lead to death or serious injury.
Caution
Ignoring the content marked by this indication and using the product incorrectly may
lead to injury or property damage.
Jeep
Model
Year
Wrangler Unlimited
2007 - 2014
* The specified vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is
not guaranteed if the manufacturer has made production changes to the listed vehicles above.
Warning: Before you begin wiring, remove the ground wire from the NEGATIVE (-)
terminal of the battery. Failing to do so can lead to electric shock, injury or damage
to equipment.