Asko WL6511XXL User manual WL6511XXL Use & Care Guide EN (English UCG 2+1 - Page 20

Care and maintenance instructions

Page 20 highlights

Care and maintenance instructions Proper care of your washer can extend its life. This section explains how to care for your washer properly and safely. Cleaning your washer Exterior - Wipe up detergent, bleach, and other spills with a soft, damp cloth or sponge as they occur. Do not use any solvents, as these can damage the machine. Interior - Clean interior with 250ml (1 cup) of chlorine bleach mixed with 500ml (2 cups) of detergent. Run washer through a complete cycle. Repeat this process if necessary. Winter storage or moving care Install and store your washer where it will not freeze. Because some water may stay in the hoses, freezing can damage your washer. If you store or move your washer during freezing weather, winterize it. To winterize washer 1. Turn off water faucet. 2. Disconnect and drain water inlet hoses. 3. Run washer on a drain and spin setting for 1 minute. 4. Unplug the power supply cord. 5. Open the drain pump cover and remove the coin trap insert. Use a shallow bowl or old towels to catch the water that drains from the unit. Replace the coin trap and close the drain pump cover. Non-use or vacation care Operate your washer only when you are at home. If you are on vacation or don't use your washer for an extended period of time, you should: • Unplug the power supply cord or turn off power to the washer. • Turn off the water supplier to the washer. This helps avoid accidental flooding (due to a water pressure surge) while you are away. Cleaning the water inlet filter If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. 1. Pull the power plug out before cleaning it. 2. Turn off the water supply to the washer and separate the inlet hose. 3. Pull the inlet filter out. Remove the dirt from the inlet filter with a brush. 4. Put the inlet filter back. Tighten the inlet hose. 20 Customer Care Center 1-800-898-1879 www.askousa.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31

20
Customer Care Center
1-800-898-1879
www.askousa.com
Care and maintenance instructions
Proper care of your washer can extend its
life. This section explains how to care for
your washer properly and safely.
Cleaning your washer
Exterior
- Wipe up detergent, bleach,
and other spills with a soft, damp cloth
or sponge as they occur. Do not use any
solvents, as these can
damage the machine.
Interior
- Clean interior with
250ml (1 cup) of chlorine
bleach mixed with 500ml
(2 cups) of detergent. Run
washer through a complete
cycle.
Repeat this process if necessary.
Winter storage or moving care
Install and store your washer where it will
not freeze. Because some water may stay
in the hoses, freezing can damage your
washer. If you store or move your washer
during freezing weather, winterize it.
To winterize washe
r
Turn off water faucet.
1.
Disconnect and drain water inlet hoses.
2.
Run washer on a drain and spin setting
3.
for 1 minute.
Unplug the power supply cord.
4.
Open the drain pump cover and remove
5.
the coin trap insert. Use a shallow bowl
or old towels to catch the water that
drains from the unit. Replace the coin
trap and close the drain pump cover.
Non-use or vacation care
Operate your washer only when you are at
home.
If you are on vacation or don’t use your
washer for an extended period of time, you
should:
Unplug the power supply cord or turn
off power to the washer.
Turn off the water supplier to the
washer. This helps avoid accidental
flooding (due to a water pressure surge)
while you are away.
Cleaning the water inlet filter
If your water is very hard or contains traces
of lime deposit, the water inlet filter may
become clogged.
Pull the power plug
1.
out before cleaning it.
Turn off the water
2.
supply to the washer
and separate the
inlet hose.
Pull the inlet filter
3.
out. Remove
the dirt from the
inlet filter with a
brush.
Put the inlet filter
4.
back. Tighten the
inlet hose.