Asus CUPLE-VM CUPLE-VM User Manual - Page 29

Floppy Disk Drive Connector 34-1 pin FLOPPY

Get Asus CUPLE-VM PDF manuals and user guides View all Asus CUPLE-VM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

3. HARDWARE SETUP 10) Floppy Disk Drive Connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting the single end to the board, connect the two plugs on the other end to the floppy drives. (Pin 5 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 5 plugged). NOTE: Orient the red markings on the floppy ribbon cable to PIN 1 CUPLE-VM PIN 1 CUPLE-VM Floppy Disk Drive Connector +5V (NC) IRRX GND IRTX 3. H/W SETUP Connectors 11) Standard Infrared Module Connector (5-pin IR) This connector supports an optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. You must also configure the setting through UART2 Use Infrared (see 4.4.2 I/O Device Configuration) to select whether UART2 is directed for use with COM2 or IrDA. Use the five pins as shown in Back View and connect a ribbon cable from the module to the motherboard's SIR connector according to the pin definitions. IR 1 CUPLE-VM CUPLE-VM Infrared Module Connector Front View Back View IRTX +5V GND (NC) IRRX ASUS CUPLE-VM User's Manual 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
ASUS CUPLE-VM User’s Manual
29
3. HARDWARE SETUP
Connectors
3. H/W SETUP
10) Floppy Disk Drive Connector (34-1 pin FLOPPY)
This connector supports the provided floppy drive ribbon cable. After
connecting the single end to the board, connect the
two plugs on the other end to
the floppy drives.
(Pin 5 is removed to prevent inserting in the wrong orien-
tation when using ribbon cables with pin 5 plugged).
NOTE:
Orient the red markings on
the floppy ribbon cable to
PIN 1
CUPLE-VM Floppy Disk Drive Connector
PIN 1
CUPLE-VM
11) Standard Infrared Module Connector (5-pin IR)
This connector supports an optional wireless transmitting and receiving infrared
module. This module mounts to a small opening on system cases that support
this feature. You must also configure the setting through
UART2 Use Infrared
(see
4.4.2 I/O Device Configuration)
to select whether UART2 is directed for
use with COM2 or IrDA. Use the five pins as shown in Back View and connect
a ribbon cable from the module to the motherboard’s SIR connector according
to the pin definitions.
CUPLE-VM
CUPLE-VM Infrared Module Connector
Front View
Back View
+5V
IRTX
IRRX
(NC)
GND
+5V
IRRX
IRTX
(NC)
GND
IR
1