Asus CUSL2-C BP CUSL2-C BP User Manual - Page 36

Power Supply PWR_FAN, CPU CPU_FAN, Chassis CHA_FAN Fan

Get Asus CUSL2-C BP PDF manuals and user guides View all Asus CUSL2-C BP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

3. HARDWARE SETUP 10) IDE Activity LED (2-pin IDELED) This connector supplies power to the cabinet's IDE activity LED. Read and write activity by devices connected to the Primary or Secondary IDE connectors will cause the LED to light up. 3. H/W SETUP Connectors TIP: If the case-mounted LED does not light, try reversing the 2-pin plug. ® CUSL2-C BP IDELED CUSL2-C BP IDE Activity LED 11) Power Supply (PWR_FAN), CPU (CPU_FAN), Chassis (CHA_FAN) Fan Connectors (3 pins) These connectors support cooling fans of 350mA (4.2 Watts) or less. Orient the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of the connector. NOTE: The "Rotation" signal is to be used only by a specially designed fan with rotation signal. The Rotations per Minute (RPM) can be read directly from the ASUS iPanel or monitored using a utility such as ASUS PC Probe or Intel LDCM. WARNING! The CPU and/or motherboard will overheat if there is no airflow across the CPU and onboard heatsinks. Damage may occur to the motherboard and/or the CPU fan if these pins are incorrectly used. These are not jumpers, do not place jumper caps over these pins. Rotation +12V GND ® CUSL2-C BP CUSL2-C BP 12-Volt Cooling Fan Power Rotation +12V GND CPU_FAN GND +12V Rotation PWR_FAN CHA_FAN 36 ASUS CUSL2-C Black PearlUser's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
36
ASUS CUSL2-C
Black Pearl
User’s Manual
Connectors
3. H/W SETUP
3. HARDWARE SETUP
10) IDE Activity LED (2-pin IDELED)
This connector supplies power to the cabinet’s IDE activity LED.
Read and
write activity by devices connected to the Primary or Secondary IDE connectors
will cause the LED to light up.
CUSL2-C BP
CUSL2-C BP IDE Activity LED
TIP:
If the case-mounted LED does not
light, try reversing the 2-pin plug.
IDELED
11)Power Supply (PWR_FAN), CPU (CPU_FAN), Chassis (CHA_FAN) Fan
Connectors (3 pins)
These connectors support cooling fans of 350mA (4.2 Watts) or less. Orient the
fans so that the heat sink fins allow airflow to go across the onboard heat sink(s)
instead of the expansion slots. Depending on the fan manufacturer, the wiring
and plug may be different. The red wire should be positive, while the black
should be ground. Connect the fan’s plug to the board taking into consideration
the polarity of the connector.
NOTE:
The “Rotation” signal is to be used only by a specially designed fan with
rotation signal. The Rotations per Minute (RPM) can be read directly from the
ASUS iPanel or monitored using a utility such as ASUS PC Probe or Intel LDCM.
WARNING!
The CPU and/or motherboard will overheat if there is no airflow
across the CPU and onboard heatsinks.
Damage may occur to the motherboard
and/or the CPU fan if these pins are incorrectly used.
These are not jumpers,
do not place jumper caps over these pins.
CUSL2-C BP
CUSL2-C BP 12-Volt
Cooling Fan Power
CPU_FAN
GND
Rotation
+12V
PWR_FAN
GND
Rotation
+12V
CHA_FAN
GND
Rotation
+12V