Asus M2V GREEN Motherboard Installation Guide - Page 36

pin SATA_E1[black], SATA_E2[black]

Get Asus M2V GREEN PDF manuals and user guides View all Asus M2V GREEN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

4. JMicron JMB363® Serial ATA RAID connectors (7-pin SATA_E1[black], SATA_E2[black]) These connectors are for Serial ATA signal cables. These connectors support Serial ATA hard disk drives that you can configure for RAID through the onboard Serial ATA RAID controller. The JMicron SATA controller mode item in the BIOS is set to [IDE] by default. Set the item to [RAID] if you want to build a RAID set. See section "2.4.5 Onboard Device Configuration" for details. R GND RSATA_RXN1 RSATA_RXP1 GND RSATA_TXN1 RSATA_TXP1 GND GND RSATA_RXN2 RSATA_RXP2 GND RSATA_TXN2 RSATA_TXP2 GND M2V-MX SATA_E1 SATA_E2 M2V-MX SATA_E Connectors • Before creating a RAID set using Serial ATA hard disks, make sure that you have connected the Serial ATA signal cables and installed Serial ATA hard disk drives; otherwise, you cannot enter the JMicron® JMB363 RAID utility and SATA BIOS setup during POST. • Install an internal Serial ATA hard disk drive to SATA_E1 or SATA_E2 and an external Serial ATA hard disk drive on your system before creating the JMicron® JMB363 RAID. 1-26 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
1-26
Chapter 1: Product introduction
4.
JMicron JMB363
®
Serial ATA RAID connectors
(7-pin SATA_E1[black], SATA_E2[black])
These connectors are for Serial ATA signal cables. These connectors
support Serial ATA hard disk drives that you can configure for RAID
through the onboard Serial ATA RAID controller.
The
JMicron SATA controller mode item in the BIOS is set to [IDE] by
default. Set the item to [RAID] if you want to build a RAID set. See
section “2.4.5 Onboard Device Configuration” for details.
•
Before creating a RAID set using Serial ATA hard disks, make sure
that you have connected the Serial ATA signal cables and installed
Serial ATA hard disk drives; otherwise, you cannot enter the
JMicron
®
JMB363 RAID utility and SATA BIOS setup during POST.
•
Install an internal Serial ATA hard disk drive to SATA_E1 or SATA_E2
and an external Serial ATA hard disk drive on your system before
creating the JMicron
®
JMB363 RAID.
M2V-MX
M2V-MX
SATA_E Connectors
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA_E1
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA_E2