Asus M3A GREEN User Manual - Page 42

Serial ATA connectors 7-pin SATA1-6

Page 42 highlights

4. Serial ATA connectors (7-pin SATA1-6) These connectors are for the Serial ATA signal cables for Serial ATA 3Gb/s hard disk and optical disk drives. The Serial ATA 3Gb/s is backward compatible with Serial ATA 1.5Gb/s specification. The data transfer rate of the Serial ATA 3Gb/s is faster than the standard parallel ATA with 133 MB/s (Ultra DMA133). If you install Serial ATA hard disk drives, you can create a RAID 0, RAID 1, and RAID 10 configuration through the onboard controller. GND RSATA_RXN4 RSATA_TXP4 GND RSATA_TXN4 RSATA_TXP4 GND GND RSATA_RXN3 RSATA_TXP3 GND RSATA_TXN3 RSATA_TXP3 GND M3A-H/HDMI ® GND RSATA_RXN2 RSATA_TXP2 GND RSATA_TXN2 RSATA_TXP2 GND SATA3 SATA2 GND RSATA_RXN5 RSATA_TXP5 GND RSATA_TXN5 RSATA_TXP5 GND SATA4 SATA5 GND RSATA_RXN6 RSATA_TXP6 GND RSATA_TXN6 RSATA_TXP6 GND GND RSATA_RXN1 RSATA_TXP1 GND RSATA_TXN1 RSATA_TXP1 GND M3A-H/HDMI SATA connectors SATA1 SATA6 Important note on Serial ATA Install the Windows® XP Service Pack 1 before using Serial ATA. • For detailed instructions on how to configure RAID 0, RAID 1 and RAID 10, refer to the RAID manual in the support DVD. • If you intend to create a Serial ATA RAID set using these connectors, set the OnChip SATA Type item in the BIOS to [RAID]. See page 2-16 for details. Connect the right-angle side of SATA signal cable to SATA device. Or you may connect the right-angle side of SATA cable to the onboard SATA port to avoid mechanical conflict with huge graphics cards. right angle side 1-30 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106

1-30
Chapter 1: Product introduction
4.
Serial ATA connectors (7-pin SATA1-6)
These connectors are for the Serial ATA signal cables for Serial ATA
3Gb/s hard disk and optical disk drives. The Serial ATA 3Gb/s is backward
compatible with Serial ATA 1.5Gb/s specification. The data transfer rate of the
Serial ATA 3Gb/s is faster than the standard parallel ATA with 133 MB/s (Ultra
DMA133).
If you install Serial ATA hard disk drives, you can create a RAID 0, RAID 1,
and RAID 10 configuration through the onboard controller.
Important note on Serial ATA
Install the Windows
®
XP Service Pack 1 before using Serial ATA.
For detailed instructions on how to configure RAID 0, RAID 1 and RAID 10,
refer to the RAID manual in the support DVD.
If you intend to create a Serial ATA RAID set using these connectors, set
the
OnChip SATA Type
item in the BIOS to [RAID]. See page 2-16 for
details.
M3A-H/HDMI
M3A-H/HDMI SATA connectors
SATA1
GND
RSATA_RXN1
RSATA_TXP1
GND
RSATA_TXN1
RSATA_TXP1
GND
SATA2
GND
RSATA_RXN2
RSATA_TXP2
GND
RSATA_TXN2
RSATA_TXP2
GND
SATA3
GND
RSATA_RXN3
RSATA_TXP3
GND
RSATA_TXN3
RSATA_TXP3
GND
SATA6
GND
RSATA_RXN6
RSATA_TXP6
GND
RSATA_TXN6
RSATA_TXP6
GND
SATA5
GND
RSATA_RXN5
RSATA_TXP5
GND
RSATA_TXN5
RSATA_TXP5
GND
SATA4
GND
RSATA_RXN4
RSATA_TXP4
GND
RSATA_TXN4
RSATA_TXP4
GND
Connect the right-angle side of SATA signal
cable to SATA device. Or you may connect
the right-angle side of SATA cable to the
onboard SATA port to avoid mechanical
conflict with huge graphics cards.
right angle side