Asus P2B P2B User Manual - Page 32

ATX Power Switch / Soft Power Switch PWR.SW - driver

Get Asus P2B PDF manuals and user guides View all Asus P2B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

III. HARDWARE SETUP 16. Message LED Lead (MSG.LED) This indicates whether a message has been received from a fax/modem. The LED will remain lit when there is no signal and blink when there is data transfer or waiting in the inbox. This function requires ACPI OS and driver support. 17. SMI Suspend Switch Lead (SMI) This allows the user to manually place the system into a suspend mode or "Green" mode where system activity will be instantly decreased to save electricity and expand the life of certain components when the system is not in use. This 2-pin connector (see the figure below) connects to the case-mounted suspend switch. If you do not have a switch for the connector, you may use the "Turbo Switch" since it does not have a function. SMI is activated when it detects a short to open moment and therefore leaving it shorted will not cause any problems. This may require one or two pushes depending on the position of the switch. 18. ATX Power Switch / Soft Power Switch (PWR.SW) The system power is controlled by a momentary switch connected to this lead. Pushing the button once will switch the system between ON and SLEEP. Pushing the switch while in the ON mode for more than 4 seconds will turn the system off. The system power LED shows the status of the system's power. 19. Reset Switch Lead (RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting to prolong the life of the system's power supply. 20. System Power LED (PWR LED) This 3-pin connector connects the system power LED, which lights when the system is powered on and blinks when it is in sleep mode. 21. Keyboard Lock Switch Lead (KEYLOCK) This 2-pin connector connects to the case-mounted key switch to allow keyboard locking. 22. Speaker Connector (SPEAKER) This 4-pin connector connects to the case-mounted speaker. R III. H/W SETUP Connectors Message LED SMI Lead ATX Power Switch* Reset SW +5 V MLED ExtSMI# Ground PWR_SW +3VSB ResetCon Ground +5 V PLED KEYLOCK Ground Power LED Keyboard Lock +5V Ground Ground SPKR Speaker Connector * Requires an ATX power supply. P2B System Panel Connections 32 ASUS P2B User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
32
ASUS P2B User’s Manual
III. HARDWARE SETUP
Connectors
III. H/W SETUP
16. Message LED Lead (MSG.LED)
This indicates whether a message has been received from a fax/modem. The
LED will remain lit when there is no signal and blink when there is data transfer
or waiting in the inbox. This function requires ACPI OS and driver support.
17. SMI Suspend Switch Lead (SMI)
This allows the user to manually place the system into a suspend mode or “Green”
mode where system activity will be instantly decreased to save electricity and
expand the life of certain components when the system is not in use. This 2-pin
connector (see the figure below)
connects to the case-mounted suspend switch.
If you do not have a switch for the connector, you may use the “Turbo Switch”
since it does not have a function. SMI is activated when it detects a
short to open
moment and therefore leaving it shorted will not cause any problems. This may
require one or two pushes depending on the position of the switch.
18. ATX Power Switch / Soft Power Switch (PWR.SW)
The system power is controlled by a momentary switch connected to this lead.
Pushing the button once will switch the system between ON and SLEEP. Push-
ing the switch while in the ON mode for more than 4 seconds will turn the
system off. The system power LED shows the status of the system’s power.
19. Reset Switch Lead (RESET)
This 2-pin connector connects to the case-mounted reset switch for rebooting
your computer without having to turn off your power switch. This is a preferred
method of rebooting to prolong the life of the system’s power supply.
20. System Power LED (PWR LED)
This 3-pin connector connects the system power LED, which lights when the
system is powered on and blinks when it is in sleep mode.
21. Keyboard Lock Switch Lead (KEYLOCK)
This 2-pin connector connects to the case-mounted key switch to allow key-
board locking.
22.
Speaker Connector (SPEAKER)
This 4-pin connector connects to the case-mounted speaker.
P2B System Panel Connections
PLED
Ground
MLED
PWR_SW
*
Requires an ATX power supply.
+5 V
KEYLOCK
+5V
SPKR
Keyboard Lock
Speaker
Connector
Power LED
Ground
+5 V
Reset SW
SMI Lead
Message
LED
ATX Power
Switch*
ExtSMI#
+3VSB
ResetCon
Ground
Ground
Ground