Asus P5V-VM Ultra Motherboard Installation Guide - Page 35

P5V-VM ULTRA IDE Connectors

Get Asus P5V-VM Ultra PDF manuals and user guides View all Asus P5V-VM Ultra manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2. IDE connectors (40-1 pin PRI_IDE, SEC_IDE) The onboard IDE connectors are for Ultra DMA 133/100/66 signal cables. There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard's IDE connector, then select one of the following modes to configure your device(s). Drive jumper setting Single device Cable-Select or Master Two devices Cable-Select Master Slave Mode of devices Cable connector - Black Master Black Slave Gray MSlaasvteer Black or gray • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices. If any device jumper is set as "Cable-Select," make sure all other device jumpers have the same setting. PRI_IDE SEC_IDE P5V-VM ULTRA PIN 1 P5V-VM ULTRA IDE Connectors NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. ASUS P5V-VM Ultra Motherboard 1-25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
ASUS P5V-VM Ultra Motherboard
1-25
Single device
Cable-Select or Master
-
Black
Two devices
Cable-Select
Master
Black
Slave
Gray
Master
Master
Slave
Slave
2.
IDE connectors (±0-1 pin PRI_IDE, SEC_IDE)
The onboard IDE connectors are for Ultra DMA 133/100/66 signal cables.
There are three connectors on each Ultra DMA 133/100/66 signal cable:
blue, black, and gray. Connect the blue connector to the motherboard’s IDE
connector, then select one of the following modes to configure your device(s).
•
Pin 20 on the IDE connector is removed to match the covered hole on the
Ultra DMA cable connector. This prevents incorrect insertion when you
connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices.
If any device jumper is set as “Cable-Select,” make sure all other device
jumpers have the same setting.
Black or gray
Drive jumper
Mode
Cable
setting
of devices
connector
P5V-VM
ULTRA
P5V-VM ULTRA IDE Connectors
SEC_IDE
NOTE:
Orient the red markings
(usually zigzag) on the ID
E
ribbon cable to PIN 1.
PRI_IDE
PIN 1