Asus RS100-E4 User Guide - Page 32

To install secondary Serial ATA drive

Get Asus RS100-E4 - 0 MB RAM PDF manuals and user guides
UPC - 610839644315
View all Asus RS100-E4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

To install secondary Serial ATA drive: 1. If you have an ODD installed, remove the ODD bay first before you install a secondary SATA disk drive. To remove, disconnect the ODD cable and power cable then use a screwdriver to remove all four screws. 2. Locate the Serial ATA drive plate under the optical disk drive (ODD) bay. 3. Connect the Serial ATA signal cable and ATX power connectors. Use the L-type Serial ATA connector to connect to the hard drive. SATA drive plate SATA L-type connector 4. Insert the Serial ATA drive into the drive plate as shown. ATX power connector SATA signal cable 2-16 Chapter 2: Hardware setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
Chapter 2:
Hardware setup
2-16
2.
Locate the Serial ATA drive plate
under the optical disk drive (ODD)
bay.
SATA drive plate
3.
Connect the Serial ATA signal cable
and ATX power connectors. Use
the L-type Serial ATA connector to
connect to the hard drive.
SATA L-type
connector
ATX power connector
SATA signal cable
4.
Insert the Serial ATA drive into the
drive plate as shown.
To install secondary Serial ATA drive:
1.
If you have an ODD installed,
remove the ODD bay first before
you install a secondary SATA disk
drive.
To remove, disconnect the ODD
cable and power cable then use
a screwdriver to remove all four
screws.