Asus Vintage-PH1 Vintage-PH1 User''s Manual for English E1943 - Page 40

Installing a floppy disk drive

Get Asus Vintage-PH1 PDF manuals and user guides View all Asus Vintage-PH1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2.9 Installing a floppy disk drive The Vintage-PH1 system comes with one 3.25-inch drive bay for a floppy disk drive. To install a floppy disk drive: 1. Remove the front panel cover. For instructions on how to remove the front panel cover, refer to page 2-3 of section "2.3 Removing the side plate and front cover" 2. Carefully insert the floppy disk drive into the floppy drive bay until the screw holes align with the holes on the bay. 3. Secure the floppy disk drive with two screws. 4. Connect the floppy disk drive signal cable to the signal connector at the back of the drive. 5. Connect the other end of the signal cable to the floppy disk drive connector on the motherboard. 6. Connect a power cable from the power supply unit to the power connector at the back of the floppy disk drive. 6 4 2-22 Chapter 2: Basic installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
2-22
2-22
2-22
2-22
2-22
Chapter 2: Basic installation
Chapter 2: Basic installation
Chapter 2: Basic installation
Chapter 2: Basic installation
Chapter 2: Basic installation
2.9
Installing a floppy disk drive
The Vintage-PH1 system comes with one 3.25-inch drive bay for a floppy
disk drive.
To install a floppy disk drive:
1.
Remove the front panel cover.
For instructions on how to remove the front panel cover, refer to page
2-3 of section “2.3 Removing the side plate and front cover”
2.
Carefully insert the floppy disk drive into the floppy drive bay until the
screw holes align with the holes on the bay.
3.
Secure the floppy disk drive with two screws.
4.
Connect the floppy disk drive
signal cable to the signal
connector at the back of the
drive.
5.
Connect the other end of the
signal cable to the floppy disk
drive connector on the
motherboard.
6.
Connect a power cable from the
power supply unit to the power
connector at the back of the
floppy disk drive.
4
6