Behringer 150 RING MOD/NOISE/S&H/LFO Quick Start Guide - Page 1
Behringer 150 RING MOD/NOISE/S&H/LFO Manual
View all Behringer 150 RING MOD/NOISE/S&H/LFO manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Quick Start Guide 150 RING MOD/NOISE/S&H/LFO Legendary Analog Ring Modulator/ Noise/S&H/LFO Module for Eurorack Controls (6) (7) (8) (10) (1) (2) (9) (3) (11) (4) (5) (12) (18) (13) (15) (20) (14) (9) CLOCK RATE slider controls the internal clock signal's rate before the clock signal is routed out through the CLOCK OUT jack. (10) S&H OUT jack sends out the final S&H (Sample & Hold) signal over cables with 3.5 mm TS connectors. (11) LAG TIME slider can be used to smooth out the changes between control voltage values as the slider is raised, similar to a portamento or glide effect on a keyboard. (12) EXT CLOCK IN input jack routes an external clock signal into the S&H circuit. (13) WAVEFORM knob selects between sine, triangle, square, ramp and sawtooth waveforms for the LFO. (14) FREQ RANGE sliding switch selects between high (H), mid (M) and low (L) frequency ranges. (15) TRIGGER jack allows a control voltage to trigger the LFO waveform by resetting the amplitude to 0. The waveform then returns to the original amplitude at a rate set by the DELAY slider. (16) FREQ slider fine-adjusts the LFO frequency within the range chosen by the FREQ RANGE switch. (17) DELAY slider controls the amount of time that elapses between the beginning of a new note and the LFO's amplitude peak. (18) FREQ CV IN input jack allows a control voltage to control the LFO frequency in place of the FREQ slider. (19) OUTPUT LEVEL sliding switch selects between a full-strength LFO output signal (x1 setting) and a 1/10th-strength signal (x 1/10 setting). (20) LFO OUT output jacks offer dual LFO outputs for use with cables with 3.5 mm TS connectors. (16) (17) (19) Power Connection (1) EXT SIG X/NOISE jack routes audio signals or noise into the ring modulator. The audio signal or noise coming in through the EXT SIG X/NOISE jack is combined with and modulated by the carrier signal routed into the EXT SIG Y/LFO jack. (2) EXT SIG Y/LFO jack routes the carrier signal into the ring modulator. The carrier signal can be in the audio range, such as a 500 Hz sine wave, or a signal from Low Frequency Oscillator (LFO). The 150 RING MOD/NOISE/S&H/LFO module comes with the required power cable for connecting to a standard Eurorack power (3) R.M OUT jack sends out the final ring modulator signal. (4) PINK output jacks offer dual white pink noise outputs for use other modules. (5) WHITE output jacks offer dual white noise outputs for use supply system. Follow these steps to connect power to the module. It is easier to make these connections before the module has been mounted into a rack case. 1. Turn the power supply or rack case power off and disconnect the power cable. with other modules. (6) EXT SIG input jack routes external signals into the S&H circuit for processing. Use the EXT/LFO/NOISE switch to optimize the EXT SIG input for different types of signals. 2. Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have (7) EXT/LFO/NOISE sliding switch optimizes the EXT SIG for use with control signals (EXT), signals from a Low Frequency a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable. Oscillator (LFO) or noise signals (NOISE). (8) CLOCK OUT jack sends out a clock signal generated inside the S&H circuit.