Behringer 150 RING MOD/NOISE/S&H/LFO Quick Start Guide - Page 2
Installation, Specifications
View all Behringer 150 RING MOD/NOISE/S&H/LFO manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
3. Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation. 4. After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply. Installation The necessary screws are included with the module for mounting in a Eurorack case. Connect the power cable before mounting. Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track that allows individual threaded plates to slide along the length of the case. The free-moving threaded plates allow precise positioning of the module, but each plate should be positioned in the approximate relation to the mounting holes in your module before attaching the screws. Hold the module against the Eurorack rails so that each of the mounting holes are aligned with a threaded rail or threaded plate. Attach the screws part way to start, which will allow small adjustments to the positioning while you get them all aligned. After the final position has been established, tighten the screws down. Specifications Signal Connections Ring modulator Ext signal X / Y X Impedance Y impedance Maximum level R.M out Impedance Maximum level Noise generator White Impedance Output level Pink Impedance Output level S & H Ext signal Impedance Maximum level Ext clock in Impedance Threshold Clock out Impedance S & H out Impedance 2 x 3.5 mm jack 100 kΩ unbalanced 100 kΩ unbalanced +20 dBu 1 x 3.5 mm jack 100 Ω unbalanced +15 dBu 2 x 3.5 mm jack 1 kΩ unbalanced 0 dBu 2 x 3.5 mm jack 1 kΩ unbalanced 0 dBu 1 x 3.5 mm jack 100 kΩ unbalanced + 17 dBu 1 x 3.5 mm jack 100 kΩ unbalanced > 1 V 1 x 3.5 mm jack 1 kΩ unbalanced 1 x 3.5 mm jack 1 kΩ unbalanced LFO Freq CV in Impedance CV input range LFO out Impedance Output level Controls S & H Clock rate Lag time Ext / LFO / noise LFO Freq range Frequency Delay Waveform Output level Power Power supply Current draw Physical Dimensions (H x W x D) Rack units Weight 1 x 3.5 mm jack 100 kΩ unbalanced 0 V to +10 V 2 x 3.5 mm jack 1 kΩ unbalanced 1 V p-p / 10 V p-p 1 x slider, 2 Hz - 25 Hz 1 x slider, 0 - 8 seconds 3-way sliding switch 3-way sliding switch High / mid / low, selectable 1 x slider, 0.03 Hz - 30 Hz in 3 ranges 1 x slider, 4 ms to 8 seconds 5-way switch Sine / triangle / square / sawtooth /inverted sawtooth, selectable 2-way sliding switch x1⁄10 / x1, selectable Eurorack 60 mA (+12 V), 50 mA (-12 V) 44 x 81 x 129 mm (1.7 x 3.2 x 5.1") 16 HP 0.16 kg (0.35 lbs) LEGAL DISCLAIMER Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved. LIMITED WARRANTY For the applicable warranty terms and conditions and additional information regarding Music Tribe's Limited Warranty, please see complete details online at musictribe.com/warranty. Zhongshan Eurotec Electronics Limited No. 10 Wanmei Road, South China Modern Chinese Medicine Park, Nanlang Town, 528451, Zhongshan City, Guangdong Province, China