Behringer EURORACK UB1832FX-PRO Manual - Page 13

Power, Level Meter, Level Setting, Pfl Level Set, Solo Normal, Main Solo, Phones Jack, Subgroups - mixer manual

Get Behringer EURORACK UB1832FX-PRO PDF manuals and user guides View all Behringer EURORACK UB1832FX-PRO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

13 EURORACK UB2442FX-PRO/UB2222FX-PRO/UB1832FX-PRO/UB1622FX-PRO User Manual POWER The blue POWER LED indicates that the device is switched on. +48 V The red "+48 V" LED lights up when phantom power is switched on. Phantom power is required to operate condenser microphones. ◊ While phantom power is switched on, do not connect or disconnect microphones on the mixer (or the stagebox/wallbox). Connect any micro-phones before switching on phantom power. Additionally, monitor/PA speakers should be muted before you activate the phantom power supply. After switching on, wait approx. one minute before adjusting the input gain so that the system has time to stabilize. LEVEL METER The high-precision level meters always give you an accurate display of signal level. LEVEL SETTING: When recording to digital recorders, the recorder's meter should not go into overload. This is because, unlike analog recordings, it takes only slightly excessive levels to create unpleasant digital distortion. When recording to analog, the VU meters of the recording machine should reach approx. +3 dB with low-frequency signals (e.g. kick drum). Due to their inertia, VU meters tend to display too low a signal level at frequencies above 1 kHz. You should only drive instruments such as a Hi-Hat as far as -10 dB. Snare drums should be driven to approx. 0 dB. ◊ The peak meters of your EURORACK display level almost independent of frequency. A recording level of 0 dB is recommended for all types of signal. ◊ The PAN control in the channel strip offers a constant power characteristic. This means that the signal is always at a constant level, irrespective of position in the stereo panorama. If the PAN control is moved fully left or right, the level in that channel increases by 4 dB. This ensures that, when set at the center of the stereo image, the audio signal does not appear louder. For this reason, with the solo function activated (Solo in Place), audio signals from channels with PAN controls that have not been moved fully left or right are displayed at a lower volume than in the PFL function. As a rule, solo signals are monitored via the control room outputs and headphones jack and are displayed by the level meters. If a solo switch is pressed, the signals from the tape input, the subgroups and the main mix are cut from these outputs and the level meter. MAIN SOLO The MAIN SOLO LED lights up as soon as a channel or aux send solo switch is pressed. The MODE switch must be set to "Solo". PFL The PFL LED indicates that the peak meter is set to PFL mode. PHONES Jack You can connect headphones to this 1/4" stereo jack (UB2442FX-PRO: 2 phones jacks). The signal routed to the PHONES connection is the same as that routed to the control room output. All Model Fig. 2.17: PHONES jack MODE The MODE switch determines whether the channels' SOLO switch operates as PFL (Pre Fader Listen) or as solo (Solo In Place). 2.3.11 Subgroups and main mix fader You use the high-precision quality faders to control the output level of the subgroups and the main mix. PFL (LEVEL SET) To activate the PFL function, press the MODE switch. The PFL function should, as a rule, be used for level setting (GAIN). The signal is sourced pre-fader and assigned to the mono PFL bus. In "PFL" mode, only the left side of the peak meter is in operation. A PFL'd channel should be driven to the 0 dB mark of the VU meter. LEFT/RIGHT switch The switches located above the subgroup faders assign the subgroup signal either to the left or right side of the main bus. Similarly, it can be routed to both sides or none at all. In the latter case, the submix is present only at the corresponding subgroup outputs. SOLO (NORMAL) When the MODE switch is not depressed, the stereo solo bus is active. Solo is actually short for "Solo In Place". This is the customary method for listening to an individual signal or to a group of signals. As soon as a solo switch is pressed, all channels not solo selected are muted in th e monitor path (control room and phones). A channel's position in the stereo image is maintained. The solo bus carries the output signals of the channel pan controls, the aux sends and the stereo line inputs. On the UB2442FX-PRO all aux returns, and on the UB1832FX-PRO only aux return 2 can be routed to the solo bus. The solo bus is, as a rule, taken post-fader. UB2442FX-PRO Fig. 2.18: Subgroup and main mix faders

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
13
EURORACK UB2442FX-PRO/UB2222FX-PRO/UB1832FX-PRO/UB1622FX-PRO User Manual
POWER
The blue
POWER
LED indicates that the device is switched on.
+48 V
The red “
+48 V
” LED lights up when phantom power is switched on.
Phantom power is required to operate condenser microphones.
◊
While phantom power is switched on, do not connect or
disconnect microphones on the mixer (or the stagebox/wallbox).
Connect any micro-phones before switching on phantom power.
Additionally, monitor/PA speakers should be muted before you activate
the phantom power supply. After switching on, wait approx. one
minute before adjusting the input gain so that the system has time
to stabilize.
LEVEL METER
The high-precision level meters always give you an accurate display of
signal level.
LEVEL SETTING:
When recording to digital recorders, the recorder’s meter should not go into
overload. This is because, unlike analog recordings, it takes only slightly excessive
levels to create unpleasant digital distortion.
When recording to analog, the VU meters of the recording machine should reach
approx. +3 dB with low-frequency signals (e.g. kick drum). Due to their inertia,
VU meters tend to display too low a signal level at frequencies above 1 kHz.
You should only drive instruments such as a Hi-Hat as far as -10 dB. Snare drums
should be driven to approx. 0 dB.
◊
The peak meters of your EURORACK display level almost independent
of frequency. A recording level of 0 dB is recommended for all types
of signal.
MODE
The
MODE
switch determines whether the channels’ SOLO switch operates as PFL
(Pre Fader Listen) or as solo (Solo In Place).
PFL (LEVEL SET)
To activate the PFL function, press the MODE switch. The PFL function should, as a
rule, be used for level setting (GAIN). The signal is sourced pre-fader and assigned
to the mono PFL bus. In “PFL” mode, only the left side of the peak meter is in
operation. A PFL’d channel should be driven to the 0 dB mark of the VU meter.
SOLO (NORMAL)
When the MODE switch is not depressed, the stereo solo bus is active. Solo is
actually short for “Solo In Place”. This is the customary method for listening to
an individual signal or to a group of signals. As soon as a solo switch is pressed,
all channels not solo selected are muted in th e monitor path (control room
and phones). A channel’s position in the stereo image is maintained. The solo
bus carries the output signals of the channel pan controls, the aux sends and
the stereo line inputs. On the
UB2442FX-PRO
all aux returns, and on the
UB1832FX-PRO
only aux return 2 can be routed to the solo bus. The solo bus is,
as a rule, taken post-fader.
◊
The PAN control in the channel strip offers a constant power
characteristic. This means that the signal is always at a constant level,
irrespective of position in the stereo panorama. If the PAN control is
moved fully left or right, the level in that channel increases by 4 dB.
This ensures that, when set at the center of the stereo image, the audio
signal does not appear louder. For this reason, with the solo function
activated (Solo in Place), audio signals from channels with PAN controls
that have not been moved fully left or right are displayed at a lower
volume than in the PFL function.
As a rule, solo signals are monitored via the control room outputs and
headphones jack and are displayed by the level meters. If a solo switch is pressed,
the signals from the tape input, the subgroups and the main mix are cut from
these outputs and the level meter.
MAIN SOLO
The
MAIN SOLO
LED lights up as soon as a channel or aux send solo switch is
pressed. The MODE switch must be set to “Solo”.
PFL
The
PFL
LED indicates that the peak meter is set to PFL mode.
PHONES Jack
You can connect headphones to this °" stereo jack (UB2442FX-PRO: 2 phones
jacks). The signal routed to the PHONES connection is the same as that routed to
the control room output.
All Model
Fig. 2.17: PHONES jack
2.3.11
Subgroups and main mix fader
You use the high-precision quality faders to control the output level of the
subgroups and the main mix.
LEFT/RIGHT switch
The switches located above the subgroup faders assign the subgroup signal
either to the left or right side of the main bus. Similarly, it can be routed to
both sides or none at all. In the latter case, the submix is present only at the
corresponding subgroup outputs.
UB2442FX-PRO
Fig. 2.18: Subgroup and main mix faders