Behringer ULTRABASS BVT5500H Manual - Page 4

ULTRABASS BVT4500H/BVT5500H 1. Introduction With the BVT4500H/5500H you have acquired a pro-level amplifier from our ULTRABASS series. This classic bass amp combines an uncompromising, "cutting-through" sound with a full range of sound-shaping features. 1.1 The Design Concept Over the past few years, flexibility has become important. Bass players must now offer a broad range of sounds and play in different venues: home studios, professional studios, and live concerts. Additionally, the world of electric bass playing has changed. New effects devices and basses, with five or six strings, are launched all the time. There is also the desire to create one's own, "unique" sound-which can only be achieved with innovative amplifiers. In response to these dual needs (flexibility and individuality), the BVT4500H/5500H offers you: == TONE and GRAPHIC EQ features-for shaping and refining sound. == VTC (Virtual Tube Circuitry)-adding the warmth of vintage tube circuitry to sound. == Jacks for connecting the BVT4500H/5500H to effects pro- cessors, mixers/recording units, other preamps, and other power amps. == 2 types of speaker jacks: ¼" TS and compatible with Neutrik Speakon connectors. 1.2 Before you get started ++ Blown fuses must be replaced by fuses of the correct rating! Please refer to the "SPECIFICATIONS" section for the applicable rating. CAUTION! ++ Before changing the fuse, switch off the device and pull the plug to avoid electric shock or damage to the device. For connection to the mains use the enclosed power cord with cold connector which complies with the relevant safety regulations. ++ Please make sure that all devices are properly grounded. For your own safety, never remove or disable the ground conductors from the devices or on the power cords. The unit must always be connected to the mains outlet with a protective grounding connection. ++ Please ensure that only qualified personnel install and operate the BVT4500H/BVT5500H. During installation and operation the user must have sufficient electrical contact to earth. Electrostatic charges might affect the operation of the unit. WARNING! ++ Extreme output volumes may damage your hearing and/ or your loudspeakers. Turn down all volume and level controls before you switch on the unit. Always set the volume to an appropriate level. 1.2.1 Shipment Your product was carefully packed at the factory to ensure safe transport. Nevertheless, if the box is damaged inspect the unit immediately for signs of damage. ++ If the unit is damaged please do NOT return it to us, but notify your dealer and the shipping company immediately; otherwise, claims for damage or replacement may not be granted. ++ We recommend that you use a flight case to give the unit optimum protection during use or transport. ++ Always use the original box to prevent damage during storage or transport. ++ Make sure that children cannot play unsupervised with the unit or its packaging. ++ Please ensure proper disposal of all packing materials. 1.2.2 Initial operation Ensure adequate air supply and to avoid overheating do not place the unit near radiators etc. Before you connect your BVT4500H/5500H to the mains, please make sure that your local voltage matches the voltage required by the unit. CAUTION: The following applies only to BVT versions that can be switched between 120 V and 230 V: The fuse holder on the mains connector has 3 triangular markings. Two of these triangles opposing each other. The device is set to the operating voltage printed next to these markers and can be set to another voltage by turning the fuse holder by 180°. ++ Please note that when operating the unit at 120 V, a higher fuse rating is required. Blown fuses must be replaced by fuses of the correct rating! ++ If you set the unit to a different mains voltage, be sure to use a fuse of the correct type and rating. Please refer to the "SPECIFICATIONS" for details. Important notes concerning installation ++ The sound quality may diminish within the range of powerful broadcasting stations and high-frequency sources. Increase the distance between the transmitter and the device and use shielded cables for all connections. 1.2.3 Online Registration Please register your new BEHRINGER equipment right after your purchase by visiting http://www.behringer.com and read the terms and conditions of our warranty carefully. Should your BEHRINGER product malfunction, it is our intention to have it repaired as quickly as possible. To arrange for warranty service, please contact the BEHRINGER retailer from whom the equipment was purchased. Should your BEHRINGER dealer not be located in your vicinity, you may directly contact one of our subsidiaries. Corresponding contact information is included in the original equipment packaging (Global Contact Information/ European Contact Information). Should your country not be listed, please contact the distributor nearest you. A list of distributors can be found in the support area of our website (http://www. behringer.com). Registering your purchase and equipment with us helps us process your repair claims more quickly and efficiently. Thank you for your cooperation! 4 Introduction