Behringer ULTRABASS BVT5500H Manual - Page 9

Audio connectors

Get Behringer ULTRABASS BVT5500H PDF manuals and user guides View all Behringer ULTRABASS BVT5500H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

ULTRABASS BVT4500H/BVT5500H 6.4 EFFECTS LOOP The EFFECTS LOOP section can be used in three ways: 6.4.1 SEND and RETURN PURPOSE: To create an effects loop, i.e., to apply external effects to the signal. RESULTS: If you use the: == BVT4500H, only the audio signal that enters via the RETURN jack continues to follow the BVT4500H signal path. The level of the effects has to be adjusted on the external unit. == BVT5500H, both the main audio signal and the audio signal that enters via the RETURN jack follow the BVT5500H signal path. To adjust the dry-wet mix, use the EFFECTS MIX control. 7. Audio connectors This section illustrates the audio connectors that you need for the BVT jacks. For details about most BVT jacks, see the section "REAR PANEL". For details about the INPUT jack, see the section "FRONT PANEL". 6.4.2 SEND only (BVT5500H only) PURPOSE: To send an audio signal from the BVT5500H to an effects processor. RESULTS: The main signal path is not affected. 6.4.3 RETURN only PURPOSE: To send an audio signal from an external pre-amp to the BVT4500H/5500H, i.e., to use the BVT as a power amp only. RESULTS: If you use the: == BVT4500H, the INPUT jack is deactivated. The signal path begins at the RETURN jack. == BVT5500H, the INPUT jack remains active. You could e.g., connect two basses to the BVT, one to INPUT and the other to RETURN. To adjust the balance between the two, use the EFFECTS MIX control. Fig. 7.1: ¼" TS connector Speaker connector (compatible with Neutrik Speakon connector) 1+ 1+ 1- 1- 6.5 INSERT CHANNEL 6.5.1 PREAMP OUTPUT PURPOSE: To process an audio signal with all BVT preamp features (TONE, EQ, EFFECTS), and then send the audio signal to an external power amp. The BVT settings affect the volume on the external amp. RESULTS: The main signal path is not affected. Fig. 7.2: The connector for a Neutrik Speakon compatible jack 6.5.2 POWER AMP IN PURPOSE: To process an audio signal with an external preamp, and then send the audio signal to the BVT4500H/5500H power amp. RESULTS: The signal path begins at the POWER AMP IN jack. The signal is independent of the MASTER control. ++ Switch off the unit before connecting an external preamp to POWER AMP IN. Fig. 7.3: XLR connectors Audio connectors 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
ULTRABASS BVT4500H/BVT5500H
Audio connectors
9
EFFECTS LOOP
6.4
The EFFECTS LOOP section can be used in three ways:
SEND and RETURN
6.4.1
PURPOSE:
To create an effects loop, i.e., to apply
external ef-
fects to the signal.
RESULTS:
If you use the:
BVT4500H, only the audio signal that enters via the
=
RETURN
jack continues to follow the BVT4500H signal path. The level
of the effects has to be adjusted on the external unit.
BVT5500H, both the main audio signal and the audio signal
=
that enters via the
RETURN
jack follow the BVT5500H sig-
nal path. To adjust the dry-wet mix, use the
EFFECTS MIX
control.
SEND only (BVT5500H only)
6.4.2
PURPOSE:
To send an audio signal from the BVT5500H to an
effects processor.
RESULTS:
The main signal path is not affected.
RETURN only
6.4.3
PURPOSE:
To send an audio signal from an external pre-amp
to the BVT4500H/5500H, i.e., to use the BVT as a power amp
only.
RESULTS:
If you use the:
BVT4500H, the
=
INPUT
jack is deactivated. The signal path
begins at the
RETURN
jack.
BVT5500H, the
=
INPUT
jack remains active. You could e.g.,
connect two basses to the BVT, one to INPUT and the other
to RETURN. To adjust the balance between the two, use the
EFFECTS MIX
control.
INSERT CHANNEL
6.5
PREAMP OUTPUT
6.5.1
PURPOSE:
To process an audio signal with all BVT preamp
features (TONE, EQ, EFFECTS), and then send the audio signal
to an external power amp. The BVT settings affect the volume on
the external amp.
RESULTS:
The main signal path is not affected.
POWER AMP IN
6.5.2
PURPOSE:
To process an audio signal with an external preamp,
and then send the audio signal to the BVT4500H/5500H power
amp.
RESULTS:
The signal path begins at the
POWER AMP IN
jack.
The signal is independent of the
MASTER
control.
Switch off the unit before connecting an external preamp
+
to POWER AMP IN.
Audio connectors
7.
This section illustrates the audio connectors that you need for
the BVT jacks. For details about most BVT jacks, see the section
“REAR PANEL”. For details about the INPUT jack, see the section
“FRONT PANEL”.
¼" TS connector
Fig. 7.1:
Speaker connector
(compatible with Neutrik Speakon connector)
1-
1-
1+
1+
The connector for a Neutrik Speakon compatible jack
Fig. 7.2:
XLR connectors
Fig. 7.3: