Behringer XENYX 802 User Manual - Page 7

XENYX 502/802/1002/1202 2.3.4 Signal assignment Fig. 2.12: Assignment switches of the main section Fig. 2.10: Monitor control and main mix fader PHONES/CONTROL ROOM The stereo PHONES jack (at the top of the connector panel) is where you connect headphones. The unbalanced CTRL ROOM OUT jacks carry the summed effects and main mix signals, as well as soloed channel signals. The PHONES/CONTROL ROOM control adjusts the level of both headphones and main monitor outputs. The 502 is not equipped with control room outputs. MAIN MIX The MAIN OUT connectors are unbalanced mono jacks. The main mix signal appears here at a level of 0 dBu. The MAIN MIX fader adjusts the volume of these outputs. The XENYX 802 and 502 mixing consoles feature a rotary control for this purpose. 2.3.3 CD/Tape connectors CD/TAPE INPUT The CD/TAPE INPUTs are used to bring an external signal source (e.g. CD player, tape deck, etc.) into the console. They can also be used as a standard stereo line input, so the output of a second XENYX or BEHRINGER ULTRALINK PRO MX882 can be connected. CD/TAPE TO MIX When the TAPE TO MIX switch is depressed, the 2-track input is assigned to the main mix providing an additional input for tape machines, MIDI instruments or other signal sources that do not require any processing. CD/TAPE TO CTRL ROOM (502: CD/TAPE TO PHONES) Press the CD/TAPE TO CTRL ROOM/PHONES switch if you want to monitor the 2-track input via the CTRL ROOM OUT. This provides an easy way to monitor signals coming back from tape to ensure that they are recording correctly. ++ If you are recording a signal via the CD/TAPE OUTPUT and wish to listen to this simultaneously via the CD/ TAPE INPUT, do not use the CD/TAPE TO MIX switch. Doing this would create a feedback loop, since the signal would be routed, via the main mix, back to tape via the CD/TAPE OUTPUT. To monitor the CD/TAPE INPUT, use the CD/TAPE TO CTRL ROOM switch to assign the tape signal to the monitor(s) or headphones. This will avoid the tape signal being routed to the CD/TAPE OUTPUT. FX TO CTRL ROOM If you want to monitor only the FX send signal in your headphones or monitor speaker(s), press the FX TO CTRL switch. This mutes the main mix signal while routing the FX SEND output to the monitor(s). The XENYX 802 and 502 do not feature this switch. 2.3.5 Phantom power and LED displays Fig. 2.13: Phantom power and control LEDs Fig. 2.11: CD/Tape input/output Alternatively the line or tape output of a hi-fi amplifier with source selection switch could also be hooked up here, allowing you to easily listen to additional sources. CD/TAPE OUTPUT These connectors are wired in parallel with the MAIN OUT and carry the main mix signal (unbalanced). Connect the CD/TAPE OUTPUT to the inputs of your recording device. The output level is adjusted via the high-precision MAIN MIX fader or rotary control (802). +48 V (802/1002/1202 only) The red +48 V LED lights up when phantom power is on. The PHANTOM switch activates the phantom power supply on the XLR connectors of all mono channels. ++ Please do not connect microphones to the mixer (or the stagebox/wallbox) as long as the phantom power supply is switched on. Connect the micro-phones before you switch on the power supply. In addition, the monitor/PA loudspeakers should be muted before you activate the phantom power supply. After switching on, wait approx. one minute in order to allow system stabilization. POWER The blue POWER LED indicates that the console is powered on. Level indicator The high-precision 4-segment display accurately displays the relevant signal level. LEVEL SETTING: To correctly set the gains of the channels, first set the LEVEL controls of the input channels to their center posi- Control elements and connectors 7