Behringer XENYX UFX1604 Quick Start Guide - Page 10

18 XENYX UFX1604 XENYX UFX1604 Controls (EN) Step 2: Controls (1) XLR balanced input. (2) LINE/HI-Z input. (3) LINE/HI-Z button. When HI-Z mode is engaged, you can plug your guitar or bass into this input without using an external direct input (D.I.) box. (4) +48 V Phantom power is used for condenser microphones that require between 9 V DC and 48 V DC power to operate. (5) LOW CUT button filters out frequencies below 80 Hz. (6) GAIN knob adjusts the sensitivity of the MIC and LINE/HI-Z inputs. (7) SEND lets you choose to route your input signal to FireWire/USB pre or post EQ. (8) COMP(RESSOR) knob adjusts the amount of compression effect on the channel. (9) EQ knobs adjust the HIGH, HIGH MID, LOW MID, and LOW frequencies of the channel. (10) EQ button turns the EQ section on and off. (11) AUX / FX A and FX B knobs adjust how much of the channel's signal is sent to the AUX SEND jacks and/or the internal FX processors. (12) PAN knob positions the channel's signal in the stereo field. (13) MUTE button removes the channel from the MAIN MIX and sends it to the ALT 3-4 bus. (14) SOLO button sends the channel signal to the solo bus (Solo in Place) or to the PFL bus (Pre-Fader Listen). (15) LEVEL METER shows the input signal level of the channel's input signal. (16) CHANNEL FADER adjusts the channel volume. (17) LINE IN left and right input jacks for mono or stereo signals. (18) LINE/FW 1-2 (3-4) button allows the signal from a computer to be routed via FireWire/USB to these channels and controlled by the EQ and AUX and Fader functions. NOTE: All FireWire (FW) routing switches work for USB connectivity to a computer and for the USB stand-alone mode depending on how you have the MODE selector switch (50) set. (19) 4-band EQ for the stereo channels. (20) BAL(ANCE) knob controls the relative volume of the left and right input signals before they are routed to the stereo main mix bus. (21) CONTROL ROOM OUT jacks carry the summed effects and main mix signals, as well as soloed channel signals. (22) MAIN OUT jacks for connecting line level signal to powered speakers or external amplifier. (23) ALT 3-4 OUT jacks for connecting line level signal of an alternate stereo mix to a recording device, powered speakers or external amplifier. Can also be used for subgrouping. (24) CD/TAPE IN and OUT for connecting a stereo source or for sending the main signal to an external recorder. (25) PHONES jacks for connecting headphones. (26) INPUT level meters display the signal input intensity going into the FX A or FX B bus. (27) FX A effect knob selects which effect is applied to the signal (same for FX B). (28) EDIT knob adjusts the effect's main parameter. (29) FX ON button turns the effect on and off. (30) The TAP/SELECT button performs two functions. Hit the button several times in the tempo of the music piece to adapt the delay time of presets 9 and 15 or the modulation speed of presets 10-12. The button will start flashing in the corresponding tempo. The TAP/SELECT button also changes the characteristic of the second parameter on presets 1-8, 13-14 and 16. By pressing the button you can toggle between two different values (light off/on) for the second parameter. 19 Quick Start Guide (31) FW/USB LED indicates the computer is connected (based on the selection switch on back panel). (32) VU METER displays the MAIN OUTPUT signal level. (33) MODE button determines whether the SOLO button operates in 'Solo in Place' (button out) or 'Pre-Fader Listen' (button in). PFL is preferred for gain setting purposes. (46) MAIN MIX stereo fader adjusts the overall output of the mixer. (47) POWER ON turns the mixer on. (48) USB DRIVE jack for use with external USB hard disk drives (recommended) or thumb drives in STAND ALONE mode. (49) USB jack for connecting to a computer. (50) MODE selector switch. (34) PHONES knob controls the volume level of (51) FireWire jack for connecting to a computer. the PHONES jacks. (52) MAIN OUTPUTS for sending MAIN MIX via (35) CONTROL RM knob controls the volume of the balanced XLR cables. CONTROL ROOM OUT jacks. (53) AUX(ILIARY) SENDS route the 4 auxiliary bus (36) SOURCE monitoring select buttons route the signals via balanced or unbalanced 1/4" cables. signal to either the CONTROL RM/PHONES jacks (left column) or the MAIN MIX (right column). (54) CHANNEL INSERTS allow you to connect external effects to the individual channels (1-8) PRE-FADER and PRE-EQ. (37) PRE/POST fader select buttons for all 4 AUX SEND busses. (55) AUX(ILIARY) RETURNS allow you to bring a stereo effects signal routed from an (38) AUX SEND 1-2 to FW 13-14 switch disables AUX SEND jack, through a processor, back into mixer channels 13-14 from being sent via the designated auxiliary bus. These inputs FireWire/USB so that AUX SEND 1-2 can be can also be used to connect additional line routed to a computer (for recording, etc.). sources such as keyboards. (39) Destination routing switches for AUX RETURN 3 source signal. (40) Destination routing switch for AUX RETURN 4 (to MAIN bus or CONTROL ROOM/PHONES bus). (41) MUTE, SOLO and output LEVEL knobs for ALT 3-4 bus. (42) Assign to FW 15-16 switch sends the MAIN MIX signal via FireWire/USB to computer or external USB drive when in the ON position. When off, mixer channels 15-16 can be sent via FireWire/USB. (43) PRE/POST switch sends the MAIN MIX signal to FireWire/USB pre or post main fader (requires ASSIGN TO FW 15-16 switch to be on). (44) TALKBACK MIC (built-in), LEVEL knob (adjusts TALKBACK microphone volume), DESTINATION switches and TALK button (press while talking). (45) 16 TRACK USB DRIVE RECORDER/MIDI TRANSPORT CONTROL for use while connected to a computer via FireWire or USB as a MIDI Machine Control. Also used In STAND ALONE MODE for controlling the internal USB recorder functions.