BenQ RP552H User Manual - Page 22

Connection, Connecting the VGA input, Connecting the touch module

Get BenQ RP552H PDF manuals and user guides View all BenQ RP552H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

18 Connection Connection Connecting the VGA input 1. Connect the VGA IN jack on the display to the VGA output jack on a computer using a D-Sub (15-pin) cable. 2. Connect the computer's audio output jack to the AUDIO IN jack on the display with a suitable audio cable. 3. To view images from this input, press the INPUT button on the remote control to switch to respective input source. Connecting the touch module Connect the TOUCH (type B) jack on the display to the USB port of a computer using the supplied USB cable. The touch module of the display supports easy Plug-and-Play operation. There is no need to install additional drivers on the computer. D-Sub (15-pin) cable USB cable Audio cable Computer • Avoid blocking the touch screen frame (where sensors are located) when initiating the touch module. • It is highly recommended that you connect the display to the PC or laptop directly. Avoid connecting the display to a face plate device which may cause failures in touch operations. • If any ghost image occurs, please try to un-plug and then re-plug all USB cables. If the failure image still exists, use another USB type B to A cable. • TOUCH must be used with HDMI or VGA IN.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Connection
18
Connection
Connecting the VGA input
1.
Connect the
VGA IN
jack on the display to the VGA output jack on a computer
using a D-Sub (15-pin) cable.
2.
Connect the computer’s audio output jack to the
AUDIO IN
jack on the display
with a suitable audio cable.
3.
To view images from this input, press the
INPUT
button on the remote control to
switch to respective input source.
Connecting the touch module
Connect the
TOUCH
(type B) jack on the display to the USB port of a computer using
the supplied USB cable. The touch module of the display supports easy Plug-and-Play
operation. There is no need to install additional drivers on the computer.
• Avoid blocking the touch screen frame (where sensors are located) when initiating the touch
module.
• It is highly recommended that you connect the display to the PC or laptop directly. Avoid
connecting the display to a face plate device which may cause failures in touch operations.
• If any ghost image occurs, please try to un-plug and then re-plug all USB cables. If the failure
image still exists, use another USB type B to A cable.
•
TOUCH
must be used with
HDMI
or
VGA IN
.
D-Sub (15-pin) cable
Audio cable
Computer
USB cable