Biostar M6TSU M6TSU user's manual - Page 26

Hard Disk Connectors: IDE1/IDE2, 6.5 Floppy Disk Connector: FDD1, 6.6 Wake On LAN Header: JWOL1

Get Biostar M6TSU PDF manuals and user guides View all Biostar M6TSU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Chapter1 Motherboard Description 1.6.4 Hard Disk Connectors: IDE1/IDE2 The motherboard has a 32-bit Enhanced, PCI IDE Controller that provides PIO Mode 0~4, and Ultra DMA 33/ 66/ 100 functionality. It has two HDD connectors IDE1 (primary) and IDE2 (secondary). You can connect up to four hard disk drives, a CD-ROM, a 120MB Floppy (reserved for future BIOS) and other devices to IDE1 and IDE2. These connectors support the IDE hard disk cable provided. IDE1 (Primary IDE Connector) The first hard drive should always be connected to IDE1. IDE1 can connect a Master and a Slave drive. You must configure the second hard drive on IDE1 to Slave mode by setting the jumper accordingly. IDE2 (Secondary IDE Connector) The IDE2 controller can also support a Master and a Slave drive. The configuration is similar to IDE1. The second driver on this controller must be set to slave mode. 1.6.5 Floppy Disk Connector: FDD1 The motherboard provides a standard floppy disk connector (FDC) that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables. 1.6.6 Wake On LAN Header: JWOL1 Pin No. Assignment 1 5V_SB 2 Ground 3 Wake up 1-20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Chapter1
Motherboard Description
1-20
1.6.4 Hard Disk Connectors: IDE1/IDE2
The motherboard has a 32-bit Enhanced, PCI IDE Controller that provides PIO
Mode 0~4, and Ultra DMA 33/ 66/ 100 functionality.
It has two HDD
connectors IDE1 (primary) and IDE2 (secondary). You can connect up to four
hard disk drives, a CD-ROM, a 120MB Floppy (reserved for future BIOS) and
other devices to IDE1 and IDE2.
These connectors support the IDE hard disk
cable provided.
±
IDE1 (Primary IDE Connector)
The first hard drive should always be connected to IDE1. IDE1 can connect a
Master and a Slave drive. You must configure the second hard drive on IDE1 to
Slave mode by setting the jumper accordingly.
±
IDE2 (Secondary IDE Connector)
The IDE2 controller can also support a Master and a Slave drive. The
configuration is similar to IDE1. The second driver on this controller must be set
to slave mode.
1.6.5 Floppy Disk Connector: FDD1
The motherboard provides a standard floppy disk connector (FDC) that supports
360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports
the provided floppy drive ribbon cables.
1.6.6 Wake On LAN Header: JWOL1
Pin No.
Assignment
1
5V_SB
2
Ground
3
Wake up