Bosch SGE78C55UC Use and Care Manuals - Page 46

Cleaning filters, Filter system,

Page 46 highlights

en-us Troubleshooting Issue Appliance interior still wet after wash cycle. Food remnants on dishware. Cause and troubleshooting Not an error. Condensation drying creates water droplets in the tub. This is normal. Moisture in the air condenses on the inside walls of the appliance, runs off, and is pumped out. No action required. Dishware was placed too close together or rack is overfilled. 1. Arrange dishware with sufficient space in be- tween. The spray jets must reach the surfaces of the dishware. 2. Avoid points of contact. Spray arm rotation of the lower spray arm is blocked. ▶ Arrange dishware so it does not obstruct spray arm rotation. Spray arm nozzles are blocked. ▶ Clean the Spray arms → Page 41. Filters are dirty. ▶ Clean the filters. → "Cleaning filters", Page 40 Filters are inserted incorrectly and/or not engaged. 1. Insert the filters properly. → "Filter system", Page 40 2. Twist filters into place. Selected wash cycle is too light. ▶ Select a more intensive wash program. Dishware has been precleaned too intensively. Then the sensors choose a lighter cycle. Stubborn remnants cannot be entirely removed. ▶ Only remove large remnants of food and do not pre-rinse dishware. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

en-us
Troubleshooting
46
Issue
Cause and troubleshooting
Appliance interior
still wet after wash
cycle.
Not an error. Condensation drying creates water
droplets in the tub. This is normal. Moisture in the
air condenses on the inside walls of the appli-
ance, runs off, and is pumped out.
No action required.
Food remnants on
dishware.
Dishware was placed too close together or rack is
overfilled.
1.
Arrange dishware with sufficient space in be-
tween.
The spray jets must reach the surfaces of the
dishware.
2.
Avoid points of contact.
Spray arm rotation of the lower spray arm is
blocked.
Arrange dishware so it does not obstruct spray
arm rotation.
Spray arm nozzles are blocked.
Clean the Spray arms
Page 41
.
Filters are dirty.
Clean the filters.
"Cleaning filters", Page 40
Filters are inserted incorrectly and/or not en-
gaged.
1.
Insert the filters properly.
"Filter system", Page 40
2.
Twist filters into place.
Selected wash cycle is too light.
Select a more intensive wash program.
Dishware has been precleaned too intensively.
Then the sensors choose a lighter cycle. Stub-
born remnants cannot be entirely removed.
Only remove large remnants of food and do not
pre-rinse dishware.