Bosch SHP7PT55UC Installation Instructions - Page 22

Warning, Caution

Get Bosch SHP7PT55UC PDF manuals and user guides View all Bosch SHP7PT55UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Water Inlet Connections WARNING Avoid Scald Hazard Do not perform any work on a charged hot water line. Serious injury could result. Only qualified plumbers should perform plumbing work. Do not attempt any work on the dishwasher hot water supply plumb- ing until you are certain the hot water supply is shut off. CAUTION Temperatures required for soldering and sweating will damage the dishwasher. If plumbing lines are to be soldered or sweated, keep the heat source at least 6 inches (152.4 mm) away from the dishwasher. Hot Water Supply The hot water heater should be set to deliver approximately 120° F (49° C) water to the dishwasher. Water that is too hot can cause some detergents to lose effectiveness. Lower water temperatures will increase run times. The hot water supply pressure must be between 15 - 145 psi (1 - 10 bar). IMPORTANT NOTES: • If using a solder joint instead of a compression fitting, be sure to make all solder connections before connecting the water supply line to the dishwasher. • Make sure there are no sharp bends or kinks in the water line that might restrict water flow. • Always use the appropriate seal when making plumbing connections. • Before connecting the water supply line to the dishwasher, flush the incoming water line for approximately 5 minutes to clear any foreign material. • Turn on the water supply and check for leaks after connections are made. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
21
WARNING
CAUTION
Avoid Scald Hazard
Do not perform any work on a charged hot water line. Serious injury
could result. Only qualified plumbers should perform plumbing work.
Do not attempt any work on the dishwasher hot water supply plumb-
ing until you are certain the hot water supply is shut off.
Temperatures required for soldering and sweating will damage the
dishwasher. If plumbing lines are to be soldered or sweated, keep the
heat source at least 6 inches (152.4 mm) away from the dishwasher.
Hot Water Supply
The hot water heater should be set to deliver approximately 120° F (49° C)
water to the dishwasher. Water that is too hot can cause some detergents
to lose effectiveness. Lower water temperatures will increase run times.
The hot water supply pressure must be between 15 - 145 psi (1 - 10 bar).
IMPORTANT NOTES:
•
If using a solder joint instead of a compression fitting, be sure to make
all solder connections before connecting the water supply line to the
dishwasher.
•
Make sure there are no sharp bends or kinks in the water line that might
restrict water flow.
•
Always use the appropriate seal when making plumbing connections.
•
Before connecting the water supply line to the dishwasher, flush the
incoming water line for approximately 5 minutes to clear any foreign
material.
•
Turn on the water supply and check for leaks after connections are
made.
Water Inlet Connections