Bosch SHPM78W55N Instructions for Use - Page 28

Switching the appliance on, Time display, Delay Start, Wash cycle end

Get Bosch SHPM78W55N PDF manuals and user guides View all Bosch SHPM78W55N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

en-us Operating the Dishwasher Switching the appliance on 1. Turn the water supply on fully. 2. Press the On/Off button (. The AUTO wash cycle has been preset as a default whenever the appliance starts. This wash cycle remains selected if no other wash cycle button 0 is pressed. Select any desired option. 3. Press Start button P. Wash cycle sequence starts. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Close the appliance door and press the Start button P again. Time display When a wash cycle is selected the remaining wash cycle time is shown on the display 8. The wash cycle time is determined during the wash cycle by the water temperature, the amount of dishes, as well as the degree of soiling and may vary (depending on the selected wash cycle). Delay Start You can delay the start of the cycle in one hour increments up to 24 hours. œ:‹, 1 hour delay œ:ƒ... 24 hours delay To set Delay start: 1. Open the door and press the On/Off button (. Select a cycle. 2. Press the Delay button from the wash cycle options H until the displayed time corresponds with your requirements. 3. Press the Start button P to activate Delay start. To cancel Delay start: 1. Open the door and press the Delay button until œ:‹‹ is indicated on the digital display 8. 2. Press the Start button P to save setting. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Press the Start button again and close the appliance door. Wash cycle end The wash cycle has ended when the display 8 reads ‹:‹‹. If the signal tone has been set, the wash cylce end is also indicated by a buzzer. Off low medium loud To change the signal volume: 1. Open the door. 2. Press the On/Off button (. 3. Hold down function key # and press Start button P until the display 8 indicates š:‹x (x can be any number). Release both buttons. 4. Press function key # until the display shows ›:‹ƒ. 5. Press function key 3. Each time the button is pressed the set value increases by one level; when it reaches the value the display jumps back to off). 6. Press Start button P to save the setting. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
en-us
Operating the Dishwasher
28
Switching the appliance on
1.
Turn the water supply on fully.
2.
Press the
On/Off
button
(
.
The AUTO wash cycle has been
preset as a default whenever the
appliance starts. This wash cycle
remains selected if no other wash
cycle button
0
is pressed.
Select any desired option.
3.
Press
Start
button
P
.
Wash cycle sequence starts.
Note:
Your dishwasher is protected
against unintentional operation. If the
appliance door remains open for
more than 4 seconds after pressing
the Start button, the operation will be
paused. Close the appliance door
and press the Start button
P
again.
Time display
When a wash cycle is selected the
remaining wash cycle time is shown
on the display
8
.
The wash cycle time is determined
during the wash cycle by the water
temperature, the amount of dishes,
as well as the degree of soiling and
may vary (depending on the selected
wash cycle).
Delay Start
You can delay the start of the cycle in
one hour increments up to 24 hours.
To set Delay start:
1.
Open the door and press the
On/Off
button
(
. Select a cycle.
2.
Press the
Delay
button from the
wash cycle options
H
until the
displayed time corresponds with
your requirements.
3.
Press the
Start
button
P
to
activate Delay start.
To cancel Delay start:
1.
Open the door and press the
Delay
button until
œ
:
‹‹
is
indicated on the digital
display
8
.
2.
Press the
Start
button
P
to
save setting.
Note:
Your dishwasher is protected
against unintentional operation. If the
appliance door remains open for
more than 4 seconds after pressing
the Start button, the operation will be
paused. Press the Start button again
and close the appliance door.
Wash cycle end
The wash cycle has ended when the
display
8
reads
‹
:
‹‹
.
If the signal tone has been set, the
wash cylce end is also indicated by a
buzzer.
To change the signal volume:
1.
Open the door.
2.
Press the
On/Off
button
(
.
3.
Hold down function key
#
and
press
Start
button
P
until the
display
8
indicates
š
:
‹
x (x can
be any number). Release both
buttons.
4.
Press function key
#
until the
display shows
›
:
‹ƒ
.
5.
Press function key
3
. Each time
the button is pressed the set
value increases by one level;
when it reaches the value
›
:
‹„
,
the display jumps back to
›
:
‹‹
(off).
6.
Press
Start
button
P
to save
the setting.
œ
:
‹‚
1 hour delay
œ
:
ƒ…
24 hours delay
›
:
‹‹
Off
›
:
‹‚
low
›
:
‹ƒ
medium
›
:
‹„
loud