Brother International BAS-326G Basic Instruction Manual - English - Page 20

Connecting the cords, INSTALLATION, <Main PCB&gt

Get Brother International BAS-326G PDF manuals and user guides View all Brother International BAS-326G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

3. INSTALLATION 3-9. Connecting the cords NOTE: • Check that the connector is facing the correct way, and then insert it firmly until it locks into place. • Secure the cables with cable ties and cord clamps, while being careful not to pull on the connector. *1 : Be sure to make the ground connection. (Refer to "3-10. Connecting the ground wire".) 1. Gently tilt back the machine head. 2. Pass the cord bundle through the hole in the work table. 3. Loosen the two screws (1), and then open the cord presser plate (2) in the direction of the right arrow and pass the cord bundle through the opening. 4. Securely connect the connectors as indicated in the table below. NOTE: • Check that the connector is facing the correct way, and then insert it firmly until it locks into place. • Secure the cables with cable ties and cord clamps, while being careful not to pull on the connector. 4924Q Lock the cord clamp securely. 1842B 12 Connector X pulse motor encoder 5-pin white Y pulse motor encoder 5-pin blue Work clamp pulse motor encoder 5-pin black Foot switch 10-pin Operation panel 8-pin Machine head switch 3-pin Home position sensor assembly 12-pin STOP switch 6-pin Valve harness 12-pin (pneumatic work clamp specifications) Programmer relay harness 8-pin Solenoid selection harness 4-pin Connection location on main PCB P20 (X-ENC) P4 (Y-ENC) P5 (P-ENC) P6 (FOOT) P1 (PANEL) P9 (HEAD-SW) P8 (SENSOR1) P13 (HEAD) P12 (AIR1) Cord clamp (3) (3) (3) (3) (3) (4) (4) (4) (4) P7 (PRG) (3) P3（CUTTER） － (Continued on next page) BAS-300G, BAS-311G, BAS-326G

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
3. INSTALLATION
BAS-300G, BAS-311G, BAS-326G
12
3-9. Connecting the cords
1. Gently tilt back the machine head.
2. Pass the cord bundle through the hole
in the work table.
3. Loosen the two screws (1), and then
open the cord presser plate (2) in the
direction of the right arrow and pass
the cord bundle through the opening.
4. Securely connect the connectors as
indicated in the table below.
NOTE:
•
Check that the connector is facing
the correct way, and then insert it
firmly until it locks into place.
•
Secure the cables with cable ties
and cord clamps, while being careful
not to pull on the connector.
<Main PCB>
NOTE:
•
Check that the connector is facing the correct
way, and then insert it firmly until it locks into
place.
•
Secure the cables with cable ties and cord
clamps, while being careful not to pull on the
connector.
*
1
: Be sure to make the ground connection.
(Refer to "3-10. Connecting the ground
wire".)
Connector
Connection location on
main PCB
Cord clamp
X pulse motor encoder 5-pin white
P20 (X-ENC)
(3)
Y pulse motor encoder 5-pin blue
P4 (Y-ENC)
(3)
Work clamp pulse motor encoder 5-pin black
P5 (P-ENC)
(3)
Foot switch 10-pin
P6 (FOOT)
(3)
Operation panel 8-pin
P1 (PANEL)
(3)
Machine head switch 3-pin
P9 (HEAD-SW)
(4)
Home position sensor assembly 12-pin
P8 (SENSOR1)
(4)
STOP switch 6-pin
P13 (HEAD)
(4)
Valve harness 12-pin (pneumatic work clamp
specifications)
P12 (AIR1)
(4)
Programmer relay harness 8-pin
P7 (PRG)
(3)
Solenoid selection harness 4-pin
P3
（
CUTTER
）
－
(Continued on next page)
4924Q
Lock the cord
clamp securely.
1842B