Brother International BAS-326G Basic Instruction Manual - English - Page 27

PREPARATION BEFORE SEWING, 4-1. Installing the needle, 4-2. Threading the upper thread

Get Brother International BAS-326G PDF manuals and user guides View all Brother International BAS-326G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

4. PREPARATION BEFORE SEWING 4. PREPARATION BEFORE SEWING 4-1. Installing the needle CAUTION Turn off the power switch before installing the needle. If the foot switch is depressed by mistake, the sewing machine might start operating and injury could result. 1. Loosen the set screw (1). 2. Insert the needle (2) in a straight line as far as it will go, making sure that the long groove on the needle is at the front, and then securely tighten the set screw (1). 2369B 4-2. Threading the upper thread Thread the upper thread correctly as shown in the illustration below. * When using threading mode for threading, the tension discs (1) will open so that the thread can be threaded more easily. (Refer to following page.) 2977B [If using cotton thread or spun thread] [If using synthetic thread] BAS-300G-03[], BAS-311G, BAS-326G BAS-300G-01[], 02[] Thread the upper thread 2370B Needle cooler 2978B • Turn the machine pulley (2) and raise the thread take-up (3) to its highest position before threading the upper thread. (This will make threading easier and it will prevent the thread from coming out at the sewing start.) • When threading the thread through the needle, allow a distance of approximately 40 mm between the needle hole and the end of the thread. If the trailing length of the thread is too long, it may cause the thread to become tangled. BAS-300G, BAS-311G, BAS-326G 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
4. PREPARATION BEFORE SEWING
19
BAS-300G, BAS-311G, BAS-326G
Needle cooler
Thread the
upper thread
4. PREPARATION BEFORE SEWING
4-1. Installing the needle
CAUTION
Turn off the power switch before installing the needle.
If the foot switch is depressed by mistake, the sewing machine might start operating and injury could result.
1. Loosen the set screw (1).
2. Insert the needle (2) in a straight line as far as it will go,
making sure that the long groove on the needle is at the
front, and then securely tighten the set screw (1).
4-2. Threading the upper thread
Thread the upper thread correctly as shown in the illustration below.
*
When using threading mode for threading, the tension discs (1) will open so that the thread can be threaded more easily.
(Refer to following page.)
•
Turn the machine pulley (2) and raise the thread take-up (3) to its highest position before threading the upper thread.
(This will make threading easier and it will prevent the thread from coming out at the sewing start.)
•
When threading the thread through the needle, allow a distance of approximately 40 mm between the needle hole and the
end of the thread.
If the trailing length of the thread is too long, it may cause the thread to become tangled.
<Standard parts>
BAS-300G-03[], BAS-311G, BAS-326G
<Option parts>
BAS-300G-01[], 02[]
2369B
2370B
[If using cotton thread or spun thread]
[If using synthetic thread]
2977B
2978B