Brother International BAS-612 Instruction Manual - English - Page 43

Approx.

Get Brother International BAS-612 PDF manuals and user guides View all Brother International BAS-612 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

< Binder position adjustment > Approx. 1 mrn ifi 0 j Cf- 9 Approx. 1 mm 1. Make sure the edge of binder 0 and the edge of carriage feed 0 are parallel and that the clearance between the two is approximately 1 mm (on both sides) when binder 0 lowers. (Adjustment) (1) Loosen bolt 0 and adjust the edge of binder 0 and the edge of carriage feed 0 so they are parallel. (2) Loosen bolt 0 and adjust the clearance between the edge of binder and the edge of carriage )i( 0 0 0 0 0 feed Q to approximately 1 mm (on both sides). 2. Make sure that the clearance between the bottom of binder and the top of slide plate is approximately 1 mm when binder lowers. (Adjustment) Loosen nut and turn shaft 0 to adjust the clearance between binder 0 bottom and slide plate 0 top to be approximately 1 mm (on both sides). Be careful to leave the same clearance to the front and rear under the bottom of binder 0 . 3. Make sure that the clearance between the bottom of cloth guide and the top of binder 0 is approximately 1 mm. (Adjustment) Loosen nut Q and adjust bolt Q) . Tighten bolt (ID to raise the binder and loosen the bolt to lower the binder. At the same time as this adjustment, raise cloth guide arm m by hand and make sure that it will return by the power of its spring. -39-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
<
Binder
position
adjustment
>
Approx.
1
mrn
ifi
Cf
-
9
0
j
Approx.
1
mm
1.
Make
sure
the
edge
of
binder
0
and
the
edge
of
carriage
feed
0
are
parallel
and
that
the
clearance
between
the
two
is
approximately
1
mm
(on
both
sides)
when
binder
0
lowers.
(Adjustment)
(1)
Loosen
bolt
0
and
adjust
the
edge
of
binder
0
and
the
edge
of
carriage
feed
0
so
they
are
parallel.
(2)
Loosen
bolt
0
and
adjust
the
clearance
between
the
edge
of
binder
and
the
edge
of
carriage
feed
Q
to
approximately
1
mm
(on
both
sides).
2.
Make
sure
that
the
clearance
between
the
bottom
of
binder
and
the
top
of
slide
plate
is
approximately
1
mm
when
binder
lowers.
(Adjustment)
Loosen
nut
and
turn
shaft
0
to
adjust
the
clearance
between
binder
0
bottom
and
slide
plate
0
top
to
be
approximately
1
mm
(on
both
sides).
Be
careful
to
leave
the
same
clearance
to
the
front
and
rear
under
the
bottom
of
binder
0
.
3.
Make
sure
that
the
clearance
between
the
bottom
of
cloth
guide
and
the
top
of
binder
0
is
approximately
1
mm.
(Adjustment)
Loosen
nut
Q
and
adjust
bolt
Q)
.
Tighten
bolt
(ID
to
raise
the
binder
and
loosen
the
bolt
to
lower
the
binder.
At
the
same
time
as
this
adjustment,
raise
cloth
guide
arm
m
by
hand
and
make
sure
that
it
will
return
by
the
power
of
its
spring.
—39—