Home » Brother International Manuals » Sewing Machines » Brother International BE-1204C » Manual Viewer

Brother International BE-1204C Instruction Manual - English - Page 245

Presser foot down error, If the cable is

Get Brother International BE-1204C PDF manuals and user guides

View all Brother International BE-1204C manuals

Add to My Manuals
Save this manual to your list of manuals

Page 245 highlights

Chapter 11 Error code list Code E-B2 E-B3 E-B4 E-B5 E-B6 E-B7 E-B8 Error Hook motor home position error Hook motor standby position error Hook motor motor mode error Hook motor communication error Hook motor parameter error Hook motor overheat error Hook motor overcurrent error E-B9 Thread trimming motor zero point error E-BA Power supply frequency error E-BC No power error E-BD E-BE E-BB, BF E-C1 Lower shaft flash memory error Lower shaft version-up error Lower shaft motor undefined error Area over during embroidering Measures This is not displayed in this model. Turn the power off and on once. If the same error occurs again, the lower shaft motor is faulty. Turn the power off and check the thread trimmer and turn the power on again. If it occurs again, the thread trimmer is faulty. It may usually occur momentarily when turning off the machine. If it occurs when the machine is on, it is a power failure detection error. This is not displayed in this model. E-C2 Wiper out error E-C3 Embroidering data buffer empty E-C4 E-C5 E-C6 E-C7 E-C8 E-C9 E-CA Presser foot down error Measured voltage value could not be received form the lower shaft motor CPU. Voltage value could not be transferred to the lower shaft motor CPU. Lower shaft error Hook motor home position error Embroidering start error No sewing permisson If the wiper is tangled with a thread, remove it. Press the or turn on the F/B switch on the head to either side. Check the connection of the communication cable of the panel. If the cable is connected correctly , press the or turn on the F/B switch on the head to either side. If the cable is disconnected , turn off the power and connect the cable. This is not displayed in this model. E-CB E-CC E-CD E-CE E-CF E-D0 E-D1 Spindle rotation speed error Shuttle thread entanglement automatic reset Speed command can not be received. Cylinder bed position error Rated voltage value could not be received from the lower shaft motor CPU. Power PC board error Cooling fan motor stop. Press the or turn on the F/B switch on the head to either side to cancel the error and press the . If the same error occurs again, there is a possibility that the spindle is overloaded. This is not usually displayed. Turn the power off and on once. If the same error occurs again, the main PCB is faulty. This is not usually displayed. Turn the power off and on once. If the same error occurs again, the power PCB is faulty. This is not usually displayed. BE-1204B-BC • BE-1206B-BC 11-5

Section	Page
Cover1	1
SAFETY INSTRUCTIONS	3
Before Starting Operation	10
Procedure of Reading This Manual	12
Contents	13
Chapter 1 An Introduction of Embroidery Machine	19
1. Specifications	20
Accessories	21
2. Software	22
2-1 Necessary Systems	22
2-2 Configuration of Software	22
2-3 Notes on use	23
2-4 Help	23
2-5 Basic Operation of Software	24
Chapter 2 Preparation of Embroidery Machine	29
1. Names of Machine Components	30
2. Installation	31
2-1 Transportation of Machine	31
2-2 Installation of Machine	33
2-3 Preparation of Needle Bar Case	34
2-4 Mounting of Table	35
2-5 Mounting of Cotton Stand	38
2-6 Lubrication to Needle Bar Case	39
2-7 Connection of Personal Computer to Machines (for connecting 4 sets)	40
2-8 Connection of Power Supply	42
2-9 Grounding	43
2-10 Installation of Software	44
3. Preparation for Embroidering	45
3-1 Upper Threading	45
3-2 Replacement of Bobbin	47
3-3 Replacing and Selecting Needle	49
3-4 Attachment of Embroidery Hoop and Frame	50
3-5 Adjustment of Thread Tension	54
Chapter 3 Embroidering Procedures	57
Functions of Operation Panel	58
Operation Panel	58
Switches at Machine Heads	60
Lamps and switches on the thread tension stand	61
Flowchart of Preparation for Embroidering	62
Run the Software	63
Turn on the Machine Power	63
Register the Machine Name	64
Retrieve the Embroidery Data	64
Start Embroidering	65
Chapter 4 Selecting and Transferring Embroidery Data	67
Functions (Command Reference)	68
Description of Screen	69
Creating a Directory	70
Transferring data	71
Copy	73
Select from Menu	73
Drag Data	73
Moving Data	74
Select from Menu	74
Drag Data	74
Deleting Data	75
Recreate an icon	76
Select All	77
Renaming Data	78
Finding Data	79
Adjusting Screen Display	81
Reading Data in Floppy Disk	82
Reading DOS Format Data	82
Converting the Non DOS format data	84
Reading Data in Paper Tape	88
Settings for Data Reading	90
Writing Data in DST Format	91
Viewing Pattern Information	92
Chapter 5 Editing Embroidery Data	93
Functions (Command Reference)	94
Description of Screen	96
Opening Embroidery Data	97
Setting Display	98
Centering	98
Zoom	98
Needle Penetration	100
Embroidering Start/End	100
Trim and pause	100
Microstitch	101
Needle Bar and Speed Range	101
Thread Color	105
Tool bar	106
Status Bar	106
Back to Previous Status	107
Undo	107
Redo	107
Editing	108
Rotate	108
Horizontal Flip	109
Vertical Flip	109
Point Symmetry	109
Repeat	109
Resize	112
Delete Stitch	112
Insert or Delete Code	113
Insert Lock Stitch	114
Changing Data	115
Changing Start	115
Changing End	116
Mask	117
Group	118
Setting Group for Repetition	119
Selecting from Menu	119
Merge	120
Saving Data	122
Save	122
Save As...	123
Viewing Pattern Information	124
Printing Data	125
Chapter 6 Embroidering	127
Functions (Command Reference)	128
When the Power to the Machine is Off	128
When the Power to the Machine is On	128
Description of Screen	131
Settings before Turning On the Machine	132
Displaying the Tool Bar	132
Displaying the Status Bar	133
Upgrading the Version of Interface Board	133
Reset Interface Board	133
Communication Port	133
Language	134
Settings after Turning Power On	135
Tool Bar	135
Status Bar	135
Zoom In	135
Zoom Out	135
Zoom In Specified Range	136
Fit to Window	136
Whole Pattern	136
Grid	137
Hoop	137
Hoop position fine adjustment	137
Needle Penetration	138
Thread Color	139
Needle Bar and Speed Range	139
Setting Needle Bar	139
Setting Ranges	143
Grid Setting	144
Background color	144
Renaming Machine	145
Viewing Machine Information	146
Design Information	146
Setting Window Display	146
Minimizing and Aligning Windows	147
Language	149
Copying Data to Other Machines	149
Configuration	150
Upgrading the Machine Program	150
Setting the Machine	151
Needle Bar	151
Same Speed Range	152
Pause	152
Speed Range	153
Head Operation Suspend	153
Hoop Feed Position	154
Embroidery Area	155
Embroidery Hoop	157
Thread Breakage Sensor	158
Automatic Step Back	159
Automatic Hoop Feed	159
End of embroidery	160
Mending	161
Adjust	162
Driving shaft	163
Activate escape with pause	163
Short stitch speed reduction	164
Thin / Thick Material	165
Area Trace	166
Trace with needle No. 1	166
Default Settings	167
Show Setting	168
Load Setting	170
Save Setting	171
Load Hoop	172
Embroidering	176
Starting Embroidering	176
Moving the Home Position	178
Step-forward/Step-back	179
Entering in the Step-forward/Step-back Mode	179
Setting Step-forward/Back Distance or Timing	180
Stepping Forward/Back	181
Resuming Embroidering	182
Moving Embroidery Position	183
Centering Pattern	184
Saving Data	185
Save	185
Save As...	185
Test	186
Running Other Programs	187
Chapter 7 Operation of Machine	189
1. Operating Procedures	190
1-1 Power Source	190
1-2 Preparation for Embroidering	190
2. Machine Stop	191
2-1 Stopping the Machine	191
2-2 Emergency Stop of the Machine	191
2-3 Resetting Emergency Stop	191
3. Permission for Hoop Movement	192
4. Measures against Thread Breakage	193
4-1 Remedies	193
4-2 Mending	194
5. Jog Embroidering	196
6. Hoop Feed Position	197
7. Area Check	198
7-1 External Tracing	198
7-2 Automatic Hoop Movement in Area	198
8. Jog Switches	199
8-1 Hoop Movement to Start Position	199
8-2 Inching Mode during Embroidering (Forcible Hoop Movement)	200
Chapter 8 Creating Production Report	201
Functions (Command Reference)	202
Description of Screen	203
Displaying Report	204
Display Example of Details	205
Display Example of Thread Breakage Information on Needle Bar	206
Display Example of Thread breakage Information in Pattern	207
Display Example of Output Information	208
Display Example of Total Output Information	210
Setting Display Items	212
General	212
Details	213
Thread Breakage Information on Needle Bar	214
Thread Breakage Information in Pattern	214
Output Information	215
Total Output Information	216
Recess Time Setting	217
Save As CSV...	218
Printing Production Report	219
Page Setup	219
Print	219
Copying Report Data	220
Chapter 9 Maintenance	221
1. Cleaning	222
1-1 Cleaning and Lubrication of Rotary Hook	222
1-2 Cleaning of Needle Plate	223
2. Oiling	224
2-1 Head	224
2-2 Lower shaft	225
3. Greasing	226
3-1 Cam grooves	226
3-2 Lower gear	228
3-3 Driving shaft	228
3-4 Needle bar flip-up mechanism	229
3-5 Feed Guide Section	230
Chapter 10 Adjustment	231
1. Adjusting Needle Bar Height	232
2. Attachment and Adjustment of Rotary Hook	236
3. Adjustment of Presser Foot Height	238
4. Thread Wiper Adjustment	239
Chapter 11 Error code list	241
Chapter 12 Troubleshooting	249
Mechanical Section	250
Electrical Section	252
Personal Computer Section	256
Chapter 13 Connection and Installation of Optional Equipment	257
1. Attaching Bobbin Winder	258

Match case Limit results 1 per page

BE-1204B-BC ° BE-1206B-BC

11-5

Chapter 11 Error code list

Code

Error

Measures

E-B2

Hook motor home position error

E-B3

Hook motor standby position error

E-B4

Hook motor motor mode error

E-B5

Hook motor communication error

E-B6

Hook motor parameter error

E-B7

Hook motor overheat error

E-B8

Hook motor overcurrent error

This is not displayed in this model.

E-B9

Thread trimming motor zero point error

Turn the power off and on once.

If the same error occurs

again, the lower shaft motor is faulty.

E-BA

Power supply frequency error

Turn the power off and check the thread trimmer and turn the

power on again.

If it occurs again, the thread trimmer is faulty.

E-BC

No power error

It may usually occur momentarily when turning off the machine.

If it occurs when the machine is on, it is a power failure

detection error.

E-BD

Lower shaft flash memory error

E-BE

Lower shaft version-up error

E-BB,

Lower shaft motor undefined error

E-C1

Area over during embroidering

This is not displayed in this model.

E-C2

Wiper out error

If the wiper is tangled with a thread, remove it.

Press the

or turn on the F/B switch on the head to either side.

E-C3

Embroidering data buffer empty

Check the connection of the communication cable of the panel.

If the cable is connected correctly , press the

or turn on

the F/B switch on the head to either side.

If the cable is

disconnected , turn off the power and connect the cable.

E-C4

Presser foot down error

E-C5

Measured voltage value could not be received

form the lower shaft motor CPU.

E-C6

Voltage value could not be transferred to the

lower shaft motor CPU.

E-C7

Lower shaft error

E-C8

Hook motor home position error

E-C9

Embroidering start error

E-CA

No sewing permisson

This is not displayed in this model.

E-CB

Spindle rotation speed error

Press the

or turn on the F/B switch on the head to either

side to cancel the error and press the

If the same error

occurs again, there is a possibility that the spindle is

overloaded.

E-CC

Shuttle thread entanglement automatic reset

This is not usually displayed.

E-CD

Speed command can not be received.

Turn the power off and on once.

If the same error occurs

again, the main PCB is faulty.

E-CE

Cylinder bed position error

E-CF

Rated voltage value could not be received from

the lower shaft motor CPU.

This is not usually displayed.

E-D0

Power PC board error

Turn the power off and on once.

If the same error occurs

again, the power PCB is faulty.

E-D1

Cooling fan motor stop.

This is not usually displayed.