Brother International LS2-B877 Instruction Manual - English and Spanish - Page 122

Adjust the Synchronizer.

Get Brother International LS2-B877 PDF manuals and user guides View all Brother International LS2-B877 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 122 highlights

15. TROUBLESHOOTING GUIDE 15. FEHLERSUCHE 15. RECHERCHES DE PANNES 15. GUIA PARA LA LOCALIZACION DE FALLAS Problem 10. Trailing lengths of the upper threads are too short after thread trimming. (-305) 33 - 37mm Trailing thread Where to check • Is the thread coming out of the cotton stand easily? If the thread is not coming out easily, check if the thread is caught on something. • Is the tension of the pretension too strong? Adjust the pretension. • Are the thread take-up spring tensions too strong? Make the thread take-up spring tensions weaker. • Are the ranges of movement for the thread take-up springs too large? Reduce the ranges of movement of the thread take-up springs. • Are the hooks of the movable knives damaged? Polish the hooks to remove the damage, or replace the damaged knife. • Are the tension discs moving during thread trimming? If the tension discs are not moving, adjust the tension release mechanism. • Is the timing correct during thread trimming? Adjust the timing for thread trimming. Page - 43 52 51 76 67 71 Hook 11. Needle up stop position is • Is the needle up stop position too low? (-305) not consistently the same. Adjust the Synchronizer. 69 • Is the V-belt tension too weak? Adjust the tension so that the V-belt shows a deflection of 10 - 14 14 mm when pushed with a finger. 12. Broken needles • Is the material being pushed or pulled with excessive force during sewing? • Does the needle pass the center of the needle hole in the feed dog? Check the needle down position. If the needle does not drop into the middle of the needle hole in the feed dog, adjust the position of the feed dog. If the needle bar has been turned, turn it again to set it to the correct position. Caution • It is extremely dangerous to leave any pieces of broken needle sticking in the material. If the needle breaks, search for all pieces until the whole of the needle is found again. • Furthermore, we recommend that thorough steps be taken to account for such needles to comply with product liability regulations. - 58 85 (Step 3) 103 LS2-B877, LT2-B878 (English)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
15. TROUBLESHOOTING GUIDE
15. FEHLERSUCHE
15. RECHERCHES DE PANNES
15. GUIA PARA LA LOCALIZACION DE FALLAS
LS2-B877, LT2-B878 (English)
103
Problem
Where to check
Page
10. Trailing lengths of the
upper threads are too
short after thread trim-
ming. (-305)
•
Is the thread coming out of the cotton stand easily?
If the thread is not coming out easily, check if the thread is caught
on something.
•
Is the tension of the pretension too strong?
Adjust the pretension.
•
Are the thread take-up spring tensions too strong?
Make the thread take-up spring tensions weaker.
•
Are the ranges of movement for the thread take-up springs too large?
Reduce the ranges of movement of the thread take-up springs.
•
Are the hooks of the movable knives damaged?
Polish the hooks to remove the damage, or replace the damaged
knife.
•
Are the tension discs moving during thread trimming?
If the tension discs are not moving, adjust the tension release mecha-
nism.
•
Is the timing correct during thread trimming?
Adjust the timing for thread trimming.
–
43
52
51
76
67
71
Hook
12. Broken needles
•
Is the material being pushed or pulled with excessive force during sew-
ing?
•
Does the needle pass the center of the needle hole in the feed dog?
Check the needle down position. If the needle does not drop into the
middle of the needle hole in the feed dog, adjust the position of the
feed dog.
If the needle bar has been turned, turn it again to set it to the correct
position.
Caution
•
It is extremely dangerous to leave any pieces of broken needle stick-
ing in the material. If the needle breaks, search for all pieces until
the whole of the needle is found again.
•
Furthermore, we recommend that thorough steps be taken to account
for such needles to comply with product liability regulations.
85
(Step 3)
11. Needle up stop position is
not consistently the same.
•
Is the needle up stop position too low? (-305)
Adjust the Synchronizer.
•
Is the V-belt tension too weak?
Adjust the tension so that the V-belt shows a deflection of 10 - 14
mm when pushed with a finger.
69
14
–
58
Trailing thread
33 - 37mm