Brother International SQ9050 Users Manual - English - Page 35

Sewing hook-and-loop, fastener

Get Brother International SQ9050 PDF manuals and user guides View all Brother International SQ9050 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

■ If thick seams are being sewn and the fabric does not feed at the beginning of stitching Zigzag foot "J" is equipped with a feature that keeps the presser foot level. a Sewing direction When you encounter a seam that is too thick a to feed under the foot, raise the presser foot lever. Press the black button on the left side of the b foot. Keep the button held in and lower the presser foot. Sewing hook-and-loop fastener CAUTION ● Use only the ungummed hook-and-loop fastener which is for sewing. If the glue is attached to the needle or the bobbin hook race, it may cause malfunction. ● If the hook-and-loop fastener is sewn with the 2 thin needle (65/9-75/11), the needle may bend or break. Note ● Before start sewing, baste together the fabric and the hook-and-loop fastener. a Black button Release the button. The foot will lock in place c level with the seam, allowing the fabric to feed. Make sure that the needle passes through the hookand-loop fastener by turning the handwheel and lower the needle into the hook-and-loop fastener before sewing. And then, sew the edge of the hookand-loop fastener at a slow speed. If the needle does not pass through the hook-andloop fastener, replace the needle with the needle for thick fabrics (page 21). a Edge of the hook-and-loop fastener • Once the trouble spot has been passed, the foot will return to its normal position. CAUTION ● If fabric more than 6 mm (15/64 inch) thick is sewn or if the fabric is pushed with too much force, the needle may bend or break. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
33
2
■
If thick seams are being sewn and the fabric does
not feed at the beginning of stitching
Zigzag foot “J” is equipped with a feature that
keeps the presser foot level.
a
Sewing direction
a
When you encounter a seam that is too thick
to feed under the foot, raise the presser foot
lever.
b
Press the black button on the left side of the
foot. Keep the button held in and lower the
presser foot.
a
Black button
c
Release the button. The foot will lock in place
level with the seam, allowing the fabric to
feed.
• Once the trouble spot has been passed, the
foot will return to its normal position.
Sewing hook-and-loop
fastener
Note
●
Before start sewing, baste together the fabric
and the hook-and-loop fastener.
Make sure that the needle passes through the hook-
and-loop fastener by turning the handwheel and
lower the needle into the hook-and-loop fastener
before sewing. And then, sew the edge of the hook-
and-loop fastener at a slow speed.
If the needle does not pass through the hook-and-
loop fastener, replace the needle with the needle for
thick fabrics (
page 21
).
a
Edge of the hook-and-loop fastener
●
If fabric more than 6 mm (15/64 inch) thick is
sewn or if the fabric is pushed with too much
force, the needle may bend or break.
CAUTION
●
Use only the ungummed hook-and-loop
fastener which is for sewing. If the glue is
attached to the needle or the bobbin hook
race, it may cause malfunction.
●
If the hook-and-loop fastener is sewn with the
thin needle (65/9-75/11), the needle may
bend or break.
CAUTION