Canon BU-47H instruction manual - Page 4

2-3. Items requiring a support wire Attach any wire to the handle section when a safety wire is required to the pan-tilt head. When attaching the wires, be careful that nothing blocks operation of the pan-tilt head. 2-4. Waterproofing the receptacle unit Inspect the waterproof connector for looseness. After pass each cable through the waterproof tube and the waterproof unit, insert the waterproof tube all the way into the waterproof connector until its tip touches the end and secure it in place. Put the end of the waterproof tube in the safe place so that water, dust and moisture do not enter. Also, do not seal the end of the waterproof tube so as to mitigate the pressure rise inside of the product caused by the temperature change. Connect each cable to the receptacle unit of the main unit, and then secure the waterproof unit to the pan-tilt head using the supplied mounting bolts (x4). Clamp the cables at appropriate intervals. Wmoautenrtpinrogobfoultnsit(x4) Fall prevention wire (for waterproof unit) Receptacle unit Waterproof unit Waterproof connector Waterproof tube (L = 500 mm) RohrFlex: RF-36 FLEXA Step 3 Connections Pan-tilt head pedestal unit When connecting the MIC cable, be sure to always use the ferrite core RFC-13 supplied with this product. Ferrite core Make one loop and then attach. Make one loop and attach the ferrite core to the cable within 10 cm from the A pan-tilt head connector. Ferrite core RFC-13 for microphone To the washer A Receptacle unit (A-A section) ᶈControl output for arbitrary function START A UX STOP CONT SDI VBS SYNC ɹᶄDigital video/ audio output ᶅSD composite signal output To the MIC unit ᶈ"69
QJO
BTTJHONFOU (HR10A-10R-10S(71)/HIROSEʣ 1 FPU 2 AUX1 3 AUX2 4 AUX3 5 AUX4 6 COM 7 8 9 10 ᶃDC power supply input ᶇCONT pin assignment ᶆExternal sync signal input (PRC05-R12M/TAJIMI) Connect power supplied from a UL-approved AC adapter or the secondary side safety circuit of a UL-approved power supply circuit. ᶇControl signal input for pan-tilt head, lens and camera* * Use the supplied RS-422 connector (PRC05-P12F/TAJIMI). Power of two or three times the rating 80 W may be consumed during power-on, so select a power supply with specifications that prevent a power failure. Pin No. Input/ output A Input B Output D Input E Output J Signal name RX+ TX+ RXTXGND ̡̢ Step 4 Checks after Completion of Connection LED START switch Back side START A UX STOP CONT SD I VBS SYNC Receptacle unit Supply power to the pan-tilt head connector (receptacle). Be sure to always perform waterproofing after supplying power. (Refer to "2-4. Waterproofing the receptacle unit".) Only for European Union and EEA (Norway, Iceland, and Liechtenstein) This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU) and national legislation. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service. For more information regarding return and recycling of WEEE products, please visit www.canon-europe.com/weee. FCC REGULATIONS This device complies with Part 15B of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15B of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canadian Radio Interface Regulations CAN ICES-3(A)/NMB-3(A) KCC-REM-CIN-BU-47H GENERAL SAFETY INFORMATION Failure to observe these warnings and cautions provided for the purpose of hazard prevention may result in injuries or accidents. Read this installation manual carefully to familiarize yourself with its contents and to ensure proper installation of this product. This installation manual uses the following symbols and terms in the warning and caution notices for preventing accidents and protecting the safety of the customer and others. WARNING Indicates a potentially hazardous situation which, if not heeded, may result in death or serious injury to you or others. Be sure to heed all warning notices to ensure safe operation at all times. CAUTION Indicates hazardous situations which, if not heeded, may result in minor or moderate injury to you or other persons, or damages to your property. NOTE Emphasizes essential inform which, if not heeded, may render the product unworkable or cause it to function improperly. Also, provides helpful information for operation. WARNING INSTALLATION 1. To prevent injury, this apparatus must be securely fixed in accordance with the installation manual. 2. This product shall not be exposed to excessive heat such as sunshine, fire or the like. 3. Do not install the unit in a location where there is a risk of combustion or ignition. When the unit is installed in a location where inflammable gas collects or is produced, ignition may result which in turn may cause a fire. CAUTION 1. When installing the unit, do not rotate the head and the camera forcibly by hand. It can cause damage to this device. 2. Do not install the unit in an unstable location such as on a wobbly table, on a sloping surface or in a location subject to severe vibration. Doing so may cause the unit to fall down or topple over, possibly causing injury. 3. Do not install the unit in a location where it may be directly exposed to salt water (seawater) or where corrosive gas or soot is present. Contact with such substances may corrode and degrade the mountings, ultimately causing the unit to fall down and possibly causing injury. 4. When transporting the unit, hold the handle of the head unit and the bottom of the unit. Otherwise, the unit may be dropped, possibly causing breakdown or injury. 5. When installing the unit in an elevated location, take appropriate measures to prevent the equipment and parts from falling. Otherwise, the equipment and parts may fall, possibly causing injury. 6. Do not install the unit in a location where it may be directly exposed to sunlight for protecting the lens. 7. The unit does not have a freeze-proof structure, so it does not move when frozen. Take care when installing the unit in a location where it may be frozen. This unit is not freeze-resistant and does not operate if frozen. Therefore, be careful when installing in a location where it may freeze. WARNING POWER SUPPLY 1. Never attempt to connect or disconnect the power cord with wet hands. Doing so may cause electric shocks. 2. Connect the power cord securely to both the input connectors and the outlet. If dust is allowed to accumulate on the exposed prongs of the power cord plug or if the prongs come into contact with metal, fire or electric shocks may result. Disconnect the power cord periodically, and use a dry cloth to wipe off any dust or dirt that has accumulated on the prongs and around the input connectors and the outlet. If the power cord is left connected for extended periods of time in locations with high levels of dust, moisture or oily smoke, the accumulated dust will absorb moisture, resulting in deterioration of the insulation and possibly fire. 3. Always remove the mounting screws before disconnecting the power cord. Placing excessive stress on the power cord may break its wires or otherwise damage the power cord, and power may leak from the damaged area, resulting in fire or electric shocks. 4. The power cord is not supplied. Using a cord that does not comply with the safety standard or is otherwise unsuitable for the installation conditions (approved product, environment) may result in fire or electric shocks. CAUTION 1. In order to ensure that the power plug can be unplugged at any time, never place objects around the power plug. Otherwise, it may be impossible to disconnect the power plug in the event of an emergency. 2. Never connect or disconnect cables until making certain that the power is turned off. Doing so may cause electric shock or damage. WARNING HANDLING THE UNIT 1. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 2. Do not allow the pan-tilt head or the inside of the housing to become wet, and do not allow water to enter inside or to be spilled onto the head. Do not put any object which contains liquid such as a drink or a vase on this product. If water has found its way inside the unit, stop using it immediately. Continuing to use the unit is a fire or electric shock hazard. Pub No. B-IM-40113-5 3. Do not attempt to disassemble or remodel the unit. High-voltage parts and intermeshing gears are to be found inside the unit, and contact with them may cause injury. 4. Do not drop the unit, bump into other objects or otherwise subject it to strong impact. If the main unit has been damaged, disconnect the power cord from the input connectors. Then contact your dealer or your Canon representative. 5. Please do not turn the lens toward the sun. When a strong light enters at the TELE side, it can cause damage to the lens and the camera. 6. When operating this device, please use a control device such as an operation unit. When panning or tilting by hand or other methods, it can cause damage to this device. CAUTION 1. Make sure that all the mountings are tightened securely. A loose mounting may cause the unit to fall down, possibly resulting in injury. 2. Periodically (every 6 months to a year as a general rule) inspect the mountings for looseness. A loose mounting may cause the unit to fall down, possibly resulting in injury. WARNING MAINTENANCE AND INSPECTION 1. Clean only with dry cloth. 2. Before cleaning the outside paneling of the unit, always disconnect the power cord from the input connectors. Furthermore, do not use benzene, paint thinners or other easily ignitable substances for cleaning purposes. Doing so is a fire and electric shock hazard. 3. This system should not be opened or disassembled, except by qualified service personnel. • Dangerous parts are to be found inside the unit, contact with them may cause finger pinch and electric shock hazard. • If foreign objects and dust enter the inside, it may cause damage to this device. • In case of high temperature and high humidity, internal damage and condensation may occur if humid air is allowed to enter this device. WARNING STORAGE 1. Before transporting the unit, return the housing to the horizontal position. When transporting the unit, place it inside the original shipping carton which was used specifically to house the unit. TO THE CUSTOMER 1. Canon shall bear no responsibility for damage resulting from improper operation of this product by the customer. 2. Canon makes no guarantees of suitability and marketability for the customer's purpose, concerning product quality, functions or this installation manual. Moreover, Canon shall bear no responsibility for any damage, direct or incidental, that results from usage for the customer's purpose. 3. Canon shall make no guarantees about the results obtained using this product. 4. The product specifications, configuration, and appearance are subject to change without prior notice. 5. For further information on repairs, maintenance, or adjustments not mentioned in this operation manual, contact your Canon dealer or your Canon sales representative. 6. Note that Canon may be unable to undertake servicing or repair of a product if it is modified without consulting Canon or your Canon sales representative. We, Canon Inc., in Japan and CANON EUROPE LTD., in U.K., confirm that the Remote pan-tilt head BU-47H is in conformity with the essential requirements of EC Directive(s) by applying the following standards EN55032 and EN55103-2 Note: a) Applicable Electromagnetic Environments: E-1 (residential), E-2 (commercial and light industrial), E-3 (urban outdoors) and E4 (controlled EMC environment, ex. TV studio). b) Use of shielded cable is required to comply with limits specified by above standards. c) Use of ferrite core is required to comply with limits specified by above standards. Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts- und Gewerbebereich sowie in Kleinbetrieben vorgesehen. CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan Canon Europe Ltd 3 The Square, Stockley Park, Uxbridge, Middlesex, UB11 1ET UK All rights reserved. No part of this operation manual may be reproduced or copied in any from or by any means without the written permission of Canon Inc. © 2015.05 CANON INC. 4/6