Cisco 2651XM Software Configuration Guide - Page 46

Frame Relay Encapsulation

Get Cisco 2651XM - VPN Bundle Router PDF manuals and user guides
UPC - 746320731841
View all Cisco 2651XM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Configuring Interface Parameters Chapter 2 Using the Setup Command Facility Note The following sections describe the prompts for each encapsulation type. For PPP and HDLC encapsulation, no further configuration is needed. No serial cable seen. Choose mode from (dce/dte) [dte]: Note If no cable is plugged in to your router, you need to indicate whether the interface is to be used as DTE or DCE. If a cable is present, the setup command facility determines the DTE/DCE status. If the serial cable is DCE, you see the following prompt: Configure IP on this interface? [no]: yes Configure IP unnumbered on this interface? [no]: IP address for this interface: 2.0.0.0 Subnet mask for this interface [255.0.0.0]: Class A network is 2.0.0.0, 0 subnet bits; mask is /8 Configure LAT on this interface? [no]: Frame Relay Encapsulation The following lmi-types are available to be set, when connected to a frame relay switch [0] none [1] ansi [2] cisco [3] q933a Enter lmi-type [2]: Note The setup command facility only prompts for the data-link connection identifier (DLCI) number if you specify none for the Local Management Interface (LMI) type. If you accept the default or specify another LMI type, the DLCI number is provided by the specified protocol. Enter the DLCI number for this interface [16]: Do you want to map a remote machine's IP address to dlci? [yes]: IP address for the remote interface: 2.0.0.2 Do you want to map a remote machine's IPX address to dlci? [yes]: IPX address for the remote interface: 40.1234.5678 Serial interface needs clock rate to be set in dce mode. The following clock rates are supported on the serial interface. 0 1200, 2400, 4800, 9600, 19200, 38400 56000, 64000, 72000, 125000, 148000, 500000 800000, 1000000, 1300000, 2000000, 4000000, 8000000 choose speed from above: [2000000]: 1200 Configure IP on this interface? [yes]: IP address for this interface: 2.0.0.1 Subnet mask for this interface [255.0.0.0]: Class A network is 2.0.0.0, 8 subnet bits; mask is /8 Note If IPX is configured on the router, the setup command facility prompts for the IPX map: Do you want to map a remote machine's IPX address to dlci? [yes]: IPX address for the remote interface: 40.0060.34c6.90ed 2-10 Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
2-10
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-04
Chapter 2
Using the Setup Command Facility
Configuring Interface Parameters
Note
The following sections describe the prompts for each encapsulation type. For PPP and HDLC
encapsulation, no further configuration is needed.
No serial cable seen.
Choose mode from (dce/dte) [dte]:
Note
If no cable is plugged in to your router, you need to indicate whether the interface is to be used as DTE
or DCE. If a cable is present, the
setup
command facility determines the DTE/DCE status. If the serial
cable is DCE, you see the following prompt:
Configure IP on this interface? [no]: yes
Configure IP unnumbered on this interface? [no]:
IP address for this interface: 2.0.0.0
Subnet mask for this interface [255.0.0.0]:
Class A network is 2.0.0.0, 0 subnet bits; mask is /8
Configure LAT on this interface? [no]:
Frame Relay Encapsulation
The following lmi-types are available to be set,
when connected to a frame relay switch
[0] none
[1] ansi
[2] cisco
[3] q933a
Enter lmi-type [2]:
Note
The
setup
command facility only prompts for the data-link connection identifier (DLCI) number if you
specify
none
for the Local Management Interface (LMI) type. If you accept the default or specify
another LMI type, the DLCI number is provided by the specified protocol.
Enter the DLCI number for this interface [16]:
Do you want to map a remote machine’s IP address to dlci? [yes]:
IP address for the remote interface: 2.0.0.2
Do you want to map a remote machine’s IPX address to dlci? [yes]:
IPX address for the remote interface: 40.1234.5678
Serial interface needs clock rate to be set in dce mode.
The following clock rates are supported on the serial interface.
0
1200, 2400, 4800, 9600, 19200, 38400
56000, 64000, 72000, 125000, 148000, 500000
800000, 1000000, 1300000, 2000000, 4000000, 8000000
choose speed from above: [2000000]: 1200
Configure IP on this interface? [yes]:
IP address for this interface: 2.0.0.1
Subnet mask for this interface [255.0.0.0]:
Class A network is 2.0.0.0, 8 subnet bits; mask is /8
Note
If IPX is configured on the router, the
setup
command facility prompts for the IPX map:
Do you want to map a remote machine's IPX address to dlci? [yes]:
IPX address for the remote interface: 40.0060.34c6.90ed