Cisco SLM2008T-NA User Guide

Cisco SLM2008T-NA Manual

Get Cisco SLM2008T-NA PDF manuals and user guides View all Cisco SLM2008T-NA manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco SLM2008T-NA manual content summary:

  • Cisco SLM2008T-NA | User Guide - Page 1
    USER GUIDE 8-Port 10/100/1000 Managed Gigabit Switch Model: SRW2008/SRW2008P/SRW2008MP BUSINESS SERIES
  • Cisco SLM2008T-NA | User Guide - Page 2
    Descriptions While reading through the User Guide you may see various icons require it. If you use an older web browser, you may have to add http:// in front of the web address. Resource Website Linksys www.linksys.com Linksys International www.linksys.com/international Glossary www.linksys
  • Cisco SLM2008T-NA | User Guide - Page 3
    the Web-based Utility 17 Setup > Summary 17 Device Information 17 System Information 18 PoE Information 18 Setup > Network Settings 18 Identification 18 IP Configuration 18 Setup > Time 19 Set Time 19 Local Time 19 Daylight Saving 19 8-Port 10/100/1000 Gigabit Switch with Webview ii
  • Cisco SLM2008T-NA | User Guide - Page 4
    21 Port Management > LACP 22 Port Management > PoE Power Settings 22 VLAN Management > Create VLAN 23 Single VLAN 23 VLAN Range 23 VLAN Table 23 VLAN Management > Port Settings 23 VLAN Management > Ports to VLAN 24 VLAN Management > VLAN to Ports 24 Join VLAN Detail 25 VLAN Management
  • Cisco SLM2008T-NA | User Guide - Page 5
    Query 52 Admin > Logging 52 Admin > Port Mirroring 53 Admin > Cable Test 53 Admin > Save Configuration 54 Via TFTP 54 Via HTTP 54 Backup 54 Admin > Firmware Upgrade 54 Admin > Reboot 55 Admin > Factory Defaults 55 Admin > Server Logs 55 8-Port 10/100/1000 Gigabit Switch with Webview iv
  • Cisco SLM2008T-NA | User Guide - Page 6
    Information 71 FCC Statement 71 Safety Notices 71 Industry Canada Statement 71 Avis d' Industrie Canada 71 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE 72 8-Port 10/100/1000 Gigabit Switch with Webview v
  • Cisco SLM2008T-NA | User Guide - Page 7
    shared MiniGBIC slots. •• SRW2008P 8-port 10/100/1000 Ethernet Switch with WebView and POE (Power over Ethernet) Includes 8 10/100/1000 RJ-45 ports and 2 shared MiniGBIC slots. For the purpose of this manual, whenever a feature applies to all models, the model number will be referenced as SRW2008x
  • Cisco SLM2008T-NA | User Guide - Page 8
    connect a serial cable to a PC's serial port for configuration using your PC's HyperTerminal program. Refer to Chapter 4: Using the Console Interface for Configuration for more information. 8-Port 10/100/1000 Gigabit Switch with Webview miniGBIC1/2 The mini-GBIC (gigabit interface converter) port
  • Cisco SLM2008T-NA | User Guide - Page 9
    4: Using the Console Interface for Configuration for more information. Back Panel The console and power ports are located on the back panel of the Switch. Back Panel POWER The Power port is where you will connect the AC power. Product Overview 8-Port 10/100/1000 Gigabit Switch with Webview 3
  • Cisco SLM2008T-NA | User Guide - Page 10
    not stack free-standing Switches more than four units high. Placement Options There are three ways to physically install the Switch, either set the Switch on its four rubber feet for desktop placement, mount the switch in a standard-sized, 19-inch 8-Port 10/100/1000 Gigabit Switch with Webview 4
  • Cisco SLM2008T-NA | User Guide - Page 11
    power strips). To rack-mount the Switch in any standard 19-inch rack, follow the instructions described below. 1. Place the Switch on a hard flat surface with the front panel facing you. 2. Attach a rack-mount bracket to one side of the Switch with the supplied screws. Then attach the other bracket
  • Cisco SLM2008T-NA | User Guide - Page 12
    -mount slots. Proper Wall-Mount Orientation (Horizontal) NOTE: Linksys is not responsible for damages incurred by insecure wall-mounting hardware. 1. Determine where you want to mount the Switch. Ensure that the wall you use is smooth, flat, dry and 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SLM2008T-NA | User Guide - Page 13
    are using the mini-GBIC port, then connect the mini-GBIC module to the mini-GBIC port. For detailed instructions, refer to the module's documentation. 6. If you will use the Switch's console interface to configure the Switch, then connect the supplied serial cable to the Switch's Console port, and
  • Cisco SLM2008T-NA | User Guide - Page 14
    HyperTerminal Connection Description Screen 8-Port 10/100/1000 Gigabit Switch with Webview HyperTerminal Properties Screen Connecting to the Switch through a Telnet Session 1. Open a command line editor and enter telnet 192.168.1.254. Then, press the Enter key. 2. The Login screen will now appear
  • Cisco SLM2008T-NA | User Guide - Page 15
    Settings 3. User and Password Settings 4. Security Settings 5. IP Configuration 6. File Management 7. Restore System Default Settings 8. Reboot System 0. Back to Main Menu. System Information From the System Information screen you can check current firmware versions and other general switch
  • Cisco SLM2008T-NA | User Guide - Page 16
    the Hardware Version. Management Settings From the Management Settings screen, you can set Serial Port Session Configuration, Telnet Session Configuration, or Secure Telnet (SSH) Configuration. Versions Boot Version This file runs when the Switch is turned on. It performs power-on diagnostics and
  • Cisco SLM2008T-NA | User Guide - Page 17
    Chapter 4 Configuration Using the Console Interface Telnet Configuration SSH Configuration On the SSH Configuration screen, you can select SSH Server Configuration, the Enter key to save your changes. To exit, select Quit and press the Enter key. 8-Port 10/100/1000 Gigabit Switch with Webview 11
  • Cisco SLM2008T-NA | User Guide - Page 18
    state or province name. (Range: 1 - 64) Country Name Specifies the country name. (Range: 2 - 2) Validity Term Specifies number of days certification is valid. (Range: 30 - 3650) User & Password Settings 8-Port 10/100/1000 Gigabit Switch with Webview 12
  • Cisco SLM2008T-NA | User Guide - Page 19
    network's default gateway is displayed. Management VLAN The VLAN ID number is displayed. DHCP client The status of the DHCP client is displayed. If you want the Switch to be a DHCP client, then select ENABLE. If you want to assign an static IP address to the Switch, then enter the IP settings and
  • Cisco SLM2008T-NA | User Guide - Page 20
    Configuration The Network Configuration screen offers a choice of two tests, Ping and TraceRoute. Network Configuration 8-Port 10/100/1000 Gigabit Switch with Webview Select Edit to change the IP address, and select Execute to begin the traceroute test. After the traceroute test is complete, the
  • Cisco SLM2008T-NA | User Guide - Page 21
    to the factory default settings, select Restore System Default Settings and press the Enter key. You will be asked if you want to continue. Press the y key to restore the Switch's default settings, or press the n key to cancel. Restore Default 8-Port 10/100/1000 Gigabit Switch with Webview Reboot
  • Cisco SLM2008T-NA | User Guide - Page 22
    Chapter 4 Configuration Using the Console Interface The Port Configuration screen displays the port numbers, their status, auto-negotiation status, speed and duplex mode, explains how to navigate the various screens of the console interface. 8-Port 10/100/1000 Gigabit Switch with Webview 16
  • Cisco SLM2008T-NA | User Guide - Page 23
    from the web-based utility: Setup, Port Management, VLAN Management, Statistics, ACL, Security, QoS (Quality of Service), Spanning Tree, Multicast, SNMP, Admin, and Logout. Click one of the main tabs to view additional tabs. Login Screen 8-Port 10/100/1000 Gigabit Switch with Webview NOTE: The LEDs
  • Cisco SLM2008T-NA | User Guide - Page 24
    PoE function is on or off. Mainpower Consumption Displays how much power is currently used. 8-Port 10/100/1000 Gigabit Switch with Webview Setup > Network Settings Setup > Network Settings The Network Settings screen allows you to assign DHCP or static IP settings to interfaces and assign default
  • Cisco SLM2008T-NA | User Guide - Page 25
    The default value is every 1024 seconds (approx. 17 minutes). Click the Save Settings button to save your changes or click Cancel Changes to discard the information. Port Management > Port Settings The Port Management > Port Settings screen shows you the settings for each of the Switch's ports. Port
  • Cisco SLM2008T-NA | User Guide - Page 26
    VLAN Edge (PVE) port, it bypasses the Forwarding Database and forwards all unicast, multicast, and broadcast traffic to an uplink. Uplinks can be ports or LAGs. Detail The Detail button will open the Port Configuration Detail screen. 8-Port 10/100/1000 Gigabit Switch with Webview Port Management
  • Cisco SLM2008T-NA | User Guide - Page 27
    port is a Private VLAN Edge (PVE) port, it bypasses the Forwarding Database and forwards all unicast, multicast, and broadcast traffic to an uplink. Click the Save Settings button to save your changes. 8-Port 10/100/1000 Gigabit Switch with Webview Port Management > Link Aggregation Port Management
  • Cisco SLM2008T-NA | User Guide - Page 28
    Long is the default. Admin Key A channel will only be formed between ports having the same admin key. This only applies to ports located on the same switch. Port Management > PoE Power Settings 8-Port 10/100/1000 Gigabit Switch with Webview Port Management > PoE Power Settings Port Displays the
  • Cisco SLM2008T-NA | User Guide - Page 29
    Port 10/100/1000 Gigabit Switch with Webview VLAN Table The VLAN Table displays a list of all configured VLANs. The VLAN ID, VLAN Name, and status of the VLAN are displayed here. To remove a VLAN, click the Remove button. VLAN Management > Port Settings VLAN Management > Port Settings The VLAN Port
  • Cisco SLM2008T-NA | User Guide - Page 30
    . General Indicates the port belongs to VLANs, and each VLAN is user-defined as tagged or untagged (full 802.1Q mode). 8-Port 10/100/1000 Gigabit Switch with Webview VLAN Management > VLAN to Ports The VLAN to Ports screen contains fields for configuring VLANs to a ports. Interface Displays the
  • Cisco SLM2008T-NA | User Guide - Page 31
    VLAN. The LAG to which it belongs can be configured to a VLAN. Join VLAN Detail The Join VLAN Detail screen allows you to select the VLAN for the port selected and determine whether it is tagged or untagged. It will values are: 8-Port 10/100/1000 Gigabit Switch with Webview Statistics > RMON
  • Cisco SLM2008T-NA | User Guide - Page 32
    Counters button This option will reset all of the statistic counts. 8-Port 10/100/1000 Gigabit Switch with Webview Refresh Now button Use default is 1800 seconds (equal to 30 minutes). Max No. of Samples to Keep Indicates the number of samples to save. Owner Displays the RMON station or user
  • Cisco SLM2008T-NA | User Guide - Page 33
    number. Owner Displays the RMON station or user that requested the RMON information. The field device was last refreshed. 8-Port 10/100/1000 Gigabit Switch with Webview CRC Align Errors Displays the contains fields for setting network alarms. Network alarms occur when a network problem, or event
  • Cisco SLM2008T-NA | User Guide - Page 34
    for either the device or in the management system. If the device is not reset, the entry remains in the Log seconds. 8-Port 10/100/1000 Gigabit Switch with Webview Owner Displays the device or user that defined RMON Event screen to configure the Event Setting table. Statistics > RMON Events Add
  • Cisco SLM2008T-NA | User Guide - Page 35
    . The possible field values are: •• No Refresh Indicates that the statistics are not refreshed. 8-Port 10/100/1000 Gigabit Switch with Webview Statistics > 802.1x Statistics Port Indicates the port, which is polled for statistics. Refresh Rate Indicates the amount of time that passes before the
  • Cisco SLM2008T-NA | User Guide - Page 36
    . 8-Port 10/100/1000 Gigabit Switch with Webview Leave resets all tables. ACL > IP based ACL ACL > IP based ACL The IP Based ACL (Access Control List) screen contains information for defining IP Based ACLs. ACL Name Displays the user-defined IP based ACLs. New ACL Name Define a new user-defined IP
  • Cisco SLM2008T-NA | User Guide - Page 37
    Psh Indicates the packet is pushed. Rst Indicates the connection is dropped. Syn Indicates request to start a session. Fin Indicates request to close a session. 8-Port 10/100/1000 Gigabit Switch with Webview Source Port Defines the TCP/UDP source port to which the ACE is matched. This field is
  • Cisco SLM2008T-NA | User Guide - Page 38
    MAC Address Matches the destination MAC address to which packets are addressed to the ACE. Wildcard Mask Defines the destination IP address wildcard mask. VLAN ID Matches the packet's VLAN ID to of the screen. Security > RADIUS 8-Port 10/100/1000 Gigabit Switch with Webview Security > RADIUS 32
  • Cisco SLM2008T-NA | User Guide - Page 39
    8-Port 10/100/1000 Gigabit Switch with Webview protocol exchanges between the device and TACACS+ server. Security > TACACS+ Host IP Address Displays the TACACS+ Server IP address. Priority Displays the order in which the TACACS+ servers are used. The default is 0. Source IP Address Displays
  • Cisco SLM2008T-NA | User Guide - Page 40
    802.1x functionality. Setting Timer 802.1x Settings > Setting Timer Port Indicates the port name. 8-Port 10/100/1000 Gigabit Switch with Webview Reauthentication Period Specifies the number of seconds in which the selected port is reauthenticated (Range: 300-4294967295). The field default is 3600
  • Cisco SLM2008T-NA | User Guide - Page 41
    Gigabit Switch with Webview Trap Frequency The amount of time (in seconds) between traps. The default value is 10 seconds. Security > Multiple Hosts The Multiple Hosts screen allows network managers to configure advanced port-based authentication settings for specific ports and VLANs. Security
  • Cisco SLM2008T-NA | User Guide - Page 42
    second) at which unknown packets are forwarded. The default value is 3500. The range is 70 - including: 8-Port 10/100/1000 Gigabit Switch with Webview •• The ingress settings. CoS is usually related to the 802.1p service that classifies flows according to their Layer 2 priority, as set in the VLAN
  • Cisco SLM2008T-NA | User Guide - Page 43
    queue for which the queue settings are displayed. The possible field range is 1 - 4. WRR Weight Displays the WRR weights to queues. 8-Port 10/100/1000 Gigabit Switch with Webview QoS > Bandwidth The Bandwidth screen allows network managers to define the bandwidth settings for a specified egress
  • Cisco SLM2008T-NA | User Guide - Page 44
    settings globally. The Bandwidth screen is not used with the Service mode, as bandwidth settings are based on services > Basic Mode 8-Port 10/100/1000 Gigabit Switch with Webview The Basic Mode management. The rules are based on the Access Control Lists (see Access Control Tab). MAC ACLs and IP
  • Cisco SLM2008T-NA | User Guide - Page 45
    the New Class Map screen. 8-Port 10/100/1000 Gigabit Switch with Webview Advanced Mode > New Class Map Class IP based ACLs. IP ACL Matches packets to IP based ACLs first, then matches packets to MAC based ACLs. Match Criteria used to match IP addresses and /or MAC addresses with an ACL's address
  • Cisco SLM2008T-NA | User Guide - Page 46
    Settings The Aggregate Policer button opens the New Aggregate Policer screen. New Aggregate Policer •• Multiple STP Provides full connectivity for packets allocated to any VLAN supports Port 10/100/1000 Gigabit Switch with Webview sending configuration messages. The default max age is 20 seconds
  • Cisco SLM2008T-NA | User Guide - Page 47
    since the bridge was initialized or reset, and the last topographic change STP on the device. Global Setting Spanning Tree State Indicates if STP Port 10/100/1000 Gigabit Switch with Webview •• Filtering Filters BPDU packets when spanning tree is disabled on an interface. This is the default
  • Cisco SLM2008T-NA | User Guide - Page 48
    traffic, however it can learn new MAC addresses. 8-Port 10/100/1000 Gigabit Switch with Webview •• Forwarding Indicates that the port is in Forwarding mode. The port can forward traffic and learn new MAC addresses. Speed Indicates the speed at which the port is operating. Path Cost Indicates the
  • Cisco SLM2008T-NA | User Guide - Page 49
    protocols. When each of the chosen network 8-Port 10/100/1000 Gigabit Switch with Webview layer protocols has been configured, packets from each settings, including region names, MSTP revisions, and maximum hops. The MSTP Properties screen contains the following fields: Region Name Provides a user
  • Cisco SLM2008T-NA | User Guide - Page 50
    port provides connectivity from a MSTP region to the outlying CIST root. •• Internal Indicates the port is an internal port. Role Indicates the port role assigned by the STP algorithm in order to provide to STP paths.The possible field values are: 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SLM2008T-NA | User Guide - Page 51
    of time host waits to receive a message before timing out. The default time is 260 seconds. MRouter Timeout Indicates the amount of the time the Multicast router waits to receive a message before it times out. The default value is 300 seconds. 8-Port 10/100/1000 Gigabit Switch with Webview 45
  • Cisco SLM2008T-NA | User Guide - Page 52
    MAC address/IP address. Bridge IP Multicast DIsplays the port that can be added to a Multicast service. LAG Displays LAG that can be added to a Multicast service. The configuration options are as follows: •• Static Indicates the port is user-defined. 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SLM2008T-NA | User Guide - Page 53
    in the Select from List field to be entered. View Type Indicates if the defined OID branch will be included or excluded in the selected SNMP view. The Add to List button adds the Views configuration to the Views Table at the bottom of the screen. 8-Port 10/100/1000 Gigabit Switch with Webview 47
  • Cisco SLM2008T-NA | User Guide - Page 54
    be made to the assigned SNMP view. 8-Port 10/100/1000 Gigabit Switch with Webview SNMP > Group Membership The Group Membership screen provides information for assigning SNMP access control privileges to SNMP groups. User name Provides a user-defined local user list. Engine ID Indicates either the
  • Cisco SLM2008T-NA | User Guide - Page 55
    Name Contains a list of user-defined SNMP views. Advanced Enables management station IP address. •• All Includes all management station IP addresses. Community String Defines the password used to authenticate the management station to the device. 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SLM2008T-NA | User Guide - Page 56
    are sent to specific users, and the trap type sent. SNMP notification filters provide the following services: •• Identifying Management Trap Targets •• Trap Filtering •• Selecting Trap Generation Parameters •• Providing Access Control Checks Recipient IP Indicates the IP address to whom the traps
  • Cisco SLM2008T-NA | User Guide - Page 57
    user name. 8-Port 10/100/1000 Gigabit Switch with Webview Admin > Static Address A static address can be assigned to a specific interface on this switch. Static addresses are bound to the assigned interface and cannot be moved. When a static address is seen on another interface, the address will
  • Cisco SLM2008T-NA | User Guide - Page 58
    information in the Dynamic MAC Address Table, including the interface type, MAC addresses, VLAN, and table storing. The Dynamic MAC Address table contains information about the aging time before a dynamic MAC 8-Port 10/100/1000 Gigabit Switch with Webview Admin > Logging Event messages have
  • Cisco SLM2008T-NA | User Guide - Page 59
    /100/1000 Gigabit Switch with Webview Admin > Cable Test Port This is the port to which the cable is connected. Test Result This is the test result. OK indicates that the cable passed the test. No Cable means there is no cable connected to the port. Open Cable means the cable is connected on only
  • Cisco SLM2008T-NA | User Guide - Page 60
    Specifies the TFTP Server IP Address to which the configuration file will be saved. •• Destination File Specifies the name of the configuration file. The default is StartupCfg.cfg. 8-Port 10/100/1000 Gigabit Switch with Webview Admin > FIrmware Upgrade The Firmware Upgrade screen contains the
  • Cisco SLM2008T-NA | User Guide - Page 61
    Admin > Factory Defaults The Factory Reset screen allows network managers to reset the device to the factory defaults shipped with the switch. Restoring factory defaults results in erasing the configuration file. Admin > Factory Defaults 8-Port 10/100/1000 Gigabit Switch with Webview Admin > Server
  • Cisco SLM2008T-NA | User Guide - Page 62
    the time the log was generated, the log severity, and a description of the log message. The Message Log is available after reboot. Admin > Flash Logs 8-Port 10/100/1000 Gigabit Switch with Webview 56
  • Cisco SLM2008T-NA | User Guide - Page 63
    when plugged into a port or connected to another cable. In Europe, the round ST connector is more prevalent. For Gigabit Ethernet, you must use the Linksys MGBT1, MGBSX1, or MGBLH1 miniGBIC modules with the Linksys Gigabit Switches. The MGBSX1 and the MGBLH1 require fiber cabling with LC connectors
  • Cisco SLM2008T-NA | User Guide - Page 64
    locate the file for download within a certain time, the device will reset. 7. Select Send File from the Transfer pull-down menu. Auto-Boot Messages 5. When the auto-boot message appears, press the Enter key to access the Startup menu. 8-Port 10/100/1000 Gigabit Switch with Webview Send File 8. In
  • Cisco SLM2008T-NA | User Guide - Page 65
    Appendix B 9. Press Send and the software is downloaded. Download After the software has been downloaded, the device will reboot automatically. Downloading Using Xmodem 8-Port 10/100/1000 Gigabit Switch with Webview 59
  • Cisco SLM2008T-NA | User Guide - Page 66
    user, and/or interface. 8-Port 10/100/1000 Gigabit Switch with Webview Baud Boot To start a device and cause it to start executing instructions. Browser An application program that provides a way to look at and interact with all the information on the World Wide Web. Bridge A device that connect
  • Cisco SLM2008T-NA | User Guide - Page 67
    speed device refraining from sending packets. FTP (File Transfer Protocol) A protocol used to transfer files over a TCP/IP network. 8-Port 10/100/1000 Gigabit Switch with Webview Full Duplex The ability of a networking device to receive and transmit data simultaneously. GARP (General Attributes
  • Cisco SLM2008T-NA | User Guide - Page 68
    power. QoS (Quality of Service) Provides policies that contain sets of filters (rules). QoS allows network managers to decide how and what network traffic is forwarded according to priorities, application types, and source and destination addresses. 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SLM2008T-NA | User Guide - Page 69
    of 0.0.0.0 indicates that all the bits are important. For example, if the destination IP address is 149.36.184.198 and the wildcard mask is 255.36.184.00, the first two bits of the IP address are used, while the last two bits are ignored. 8-Port 10/100/1000 Gigabit Switch with Webview Glossary 63
  • Cisco SLM2008T-NA | User Guide - Page 70
    2 MAC table size Number of VLANs VLAN HOL Blocking Management Web User Interface SNMP SNMP MIBs SRW2008 8 RJ-45 Connectors for 10BASE-T/100BASE-TX/ 1000Base-T with 2 shared SFP ports on port 7 and 8 (combo port) Console Port Auto MDI/MDI-X Autonegotiate/Manual Setting UTP CAT 5 or Better for
  • Cisco SLM2008T-NA | User Guide - Page 71
    STP, 802.1Q/p VLAN, 802.1w Rapid STP, 802.1s Multiple STP, 802.1x Port Access Authentication 279,4 x 44,45 x 170 mm 1 kg External AC Power Adapter FCC Part15 Class A, CE Class A, UL, cUL, CE Mark, CB 0 to 40ºC -20 to 70ºC 8-Port 10/100/1000 Gigabit Switch with Webview Operating Humidity Storage
  • Cisco SLM2008T-NA | User Guide - Page 72
    , RFC 2618 RADIUS Client MIB, RFC 1215 Traps Private POE MIB Embedded Remote Monitoring (RMON) Software Agent Supports four RMON Groups 8-Port 10/100/1000 Gigabit Switch with Webview Firmware Upgrade Port Mirroring Other Management Security Features IEEE 802.1X Access Control Availability Link
  • Cisco SLM2008T-NA | User Guide - Page 73
    to change without notice. 8-Port 10/100/1000 Gigabit Switch with Webview Model Ports Cabling Type LEDs POE Performance Switching Capacity Forwarding Rate Layer 2 MAC table size Number of VLANs VLAN HOL Blocking Management Web User Interface SNMP SNMP MIBs RMON SRW2008P 8 RJ-45 Connectors for
  • Cisco SLM2008T-NA | User Guide - Page 74
    Tree IGMP Snooping IGMP (v1/v2) snooping limits 8-Port 10/100/1000 Gigabit Switch with Webview QoS Priority levels Scheduling Class of Service Rate Limiting Standards Environmental Dimensions Unit Weight Power Certification Operating Temp. Storage Temp. Operating Humidity Storage Humidity
  • Cisco SLM2008T-NA | User Guide - Page 75
    , system or network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or 8-Port 10/100/1000 Gigabit Switch with Webview service offerings. This limited warranty shall not apply to such third
  • Cisco SLM2008T-NA | User Guide - Page 76
    be found at: www.linksys.com/support. This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623. Warranty Information 8-Port 10/100/1000 Gigabit Switch with Webview 70
  • Cisco SLM2008T-NA | User Guide - Page 77
    not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense
  • Cisco SLM2008T-NA | User Guide - Page 78
    EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required will your local authorities, waste disposal service, or the shop where you
  • Cisco SLM2008T-NA | User Guide - Page 79
    Pour plus d'informations sur le mode d'élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l'endroit où vous avez acheté le produit. Italiano (Italian) - Informazioni relative all'ambiente per i clienti residenti
  • Cisco SLM2008T-NA | User Guide - Page 80
    de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft. Norsk (Norwegian) - Miljøinformasjon for kunder i EU EU-direktiv 2002/96/EF krever at utstyr med følgende symbol avbildet på produktet og/eller pakningen, ikke må kastes sammen med usortert
  • Cisco SLM2008T-NA | User Guide - Page 81
    trgovino, kjer ste izdelek kupili. Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli itse tuotteessa ja/tai sen du köpte produkten. WEB: For additional information, please visit www.linksys.com Footer 75
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
USER GUIDE
BUSINESS SERIES
8-Port 10/100/1000
Managed Gigabit Switch
Model:
SRW2008/SRW2008P/SRW2008MP