Cisco WAG54G User Manual - Page 19

Wireless Connection to a Computer, phone and wall jack to prevent interference. - linksys 2

Get Cisco WAG54G PDF manuals and user guides View all Cisco WAG54G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Wireless-G ADSL Gateway Wireless Connection to a Computer If you want to use a wireless connection to access the Gateway, follow these instructions: 1. Before you begin, make sure that all of your network's hardware is powered off, including the Gateway and all computers. NOTE: A small device called a microfilter (not included) may be necessary between each phone and wall jack to prevent interference. Contact your ISP if you have any questions. IMPORTANT: For countries that have phone jacks with RJ-11 connectors, make sure to only place the microfilters between the phone and the wall jack and not between the Modem and the wall jack or your ADSL will not connect. For countries that do not have phone jacks with RJ-11 connectors (e.g. France, Sweden, Switzerland, United Kingdom, etc.), except for ISDN users, the microfilter has to be used between the modem and the wall jack, because the microfilter will have the RJ-11 connector. Annex B users (E1 and DE versions of the Gateway) must use the included special cable to connect the gateway to the wall jack (RJ-45 to RJ-12). If you require splitters or special jacks, please contact your service provider. 2. Connect a phone cable from the Line port on the Gateway's back panel to the wall jack of the ADSL line. A small device called a microfilter may be necessary between each phone and wall jack to prevent interference. Contact your ISP if you have any questions. 3. Connect the power adapter to the Power port, and then plug the power adapter into a power outlet. Turn the On/Off switch to On. • The Power LED on the front panel will light up green as soon as the power adapter is connected properly and the switch is turned on. The Power LED will flash for a few seconds, then light up steady when the self-test is complete. If the LED flashes for one minute or longer, see "Appendix A: Troubleshooting." 4. Power on one of the computers on your wireless network(s). 5. For initial access to the Gateway through a wireless connection, make sure the computer's wireless adapter has its SSID set to linksys (the Gateway's default setting), and its Wireless Security is disabled. After you have accessed the Gateway, you can change the Gateway and this computer's adapter settings to match the your usual network settings. The Gateway's hardware installation is now complete. Go to "Chapter 5: Configuring the Gateway." Chapter 4: Connecting the Wireless-G ADSL Gateway Wireless Connection to a Computer NOTE: You should always change the SSID from its default, linksys, and enable WEP encryption. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
12
Chapter 4: Connecting the Wireless-G ADSL Gateway
Wireless Connection to a Computer
Wireless-G ADSL Gateway
Wireless Connection to a Computer
If you want to use a wireless connection to access the Gateway, follow these instructions:
1.
Before you begin, make sure that all of your network’s hardware is powered off, including the Gateway and all
computers.
2.
Connect a phone cable from the Line port on the Gateway’s back panel to the wall jack of the ADSL line. A
small device called a microfilter may be necessary between each phone and wall jack to prevent interference.
Contact your ISP if you have any questions.
3.
Connect the power adapter to the Power port, and then plug the power adapter into a power outlet. Turn the
On/Off switch to On.
•
The Power LED on the front panel will light up green as soon as the power adapter is connected properly
and the switch is turned on. The Power LED will flash for a few seconds, then light up steady when the
self-test is complete. If the LED flashes for one minute or longer, see “Appendix A: Troubleshooting.”
4.
Power on one of the computers on your wireless network(s).
5.
For initial access to the Gateway through a wireless connection, make sure the computer’s wireless adapter
has its SSID set to linksys (the Gateway’s default setting), and its Wireless Security is disabled. After you have
accessed the Gateway, you can change the Gateway and this computer’s adapter settings to match the your
usual network settings.
The Gateway’s hardware installation is now complete.
Go to “Chapter 5: Configuring the Gateway.”
NOTE:
You should always change the SSID from its
default, linksys, and enable WEP encryption.
NOTE:
A small device called a microfilter (not included) may be necessary between each
phone and wall jack to prevent interference.
Contact your ISP if you have any questions.
IMPORTANT:
For countries that have phone jacks with RJ-11 connectors, make sure to only
place the microfilters between the phone and the wall jack and
not
between the Modem and
the wall jack or your ADSL will not connect.
For countries that do
not
have phone jacks with RJ-11 connectors (e.g. France, Sweden,
Switzerland, United Kingdom, etc.), except for ISDN users, the microfilter has to be used
between the modem and the wall jack, because the microfilter will have the RJ-11 connector.
Annex B users (E1 and DE versions of the Gateway) must use the included special cable to
connect the gateway to the wall jack (RJ-45 to RJ-12).
If you require splitters or special jacks,
please contact your service provider.