Cisco WAP200E-EU User Guide - Page 15

Advanced Configuration, Web-Based Utility, Setup > Basic Setup, Setup, Network Setup - default

Get Cisco WAP200E-EU - Small Business Wireless-G Exterior Access Point PDF manuals and user guides
UPC - 745883578627
View all Cisco WAP200E-EU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Chapter 6 Advanced Configuration Chapter 6: Advanced Configuration Open your web browser and enter http://192.168.1.245 into the Address field. Press the Enter key and the Password screen will appear. Address Bar NOTE: The default IP address is 192.168.1.245. If the IP address has been changed using DHCP or via the console interface, enter the assigned IP address instead of the default. The first time you open the web‑based utility, enter admin (the default username) in the User name field and enter it again in the Password field. Click the OK button. You can change the Access Point's password later from the Administration > Management screen. Login Screen Web-Based Utility The first screen that appears in the web-based utility is the Setup screen. This allows you to change the Access Point's general settings. There are five tabs across the top of the screen: Setup, Wireless, AP Mode, Administration, and Status. Each tab contains screens that will help you configure and manage the Access Point. Wireless-G Exterior Access Point with Power Over Ethernet Setup > Basic Setup Setup > Basic Setup Enter names for the Access Point. The host name can be used to access the Web Utility through the network if DNS has been set up. The device name is for the benefit of identifying your Access Point after you log in. Setup Host Name This is the host name assigned to the Access Point. This host name will be published to your DNS server if the Access Point is configured to acquire the IP address through DHCP. In that case, Linksys recommends to follow the company policy on the host name assignment. The default name is Linksys. Device Name You may assign any device name to the Access Point. This name is only used by the Access Point administrator for identification purposes. Unique, memorable names are helpful, especially if you are employing multiple access points on the same network. The default name is WAP200E. Network Setup The selections under this heading allow you to configure the Access Point's IP address setting(s). IP Settings Static IP Address Selected by default, this option is used to assign a static or fixed IP address to the Access Point. • LocalIPAddress TheIPaddressmustbeuniquetoyour network. The default IP address is 192.168.1.245. • Subnet Mask The Subnet Mask must be the same as that set on the LAN that your Access Point is connected to. The default is 255.255.255.0. • Default Gateway Enter the Default Gateway Address, typically this is the IP address of your router. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
Chapter ·
Advanced Configuration
²0
W±reless-G Exter±or Access Po±nt w±th Power Over Ethernet
Chapter ·:
Advanced Conf±gurat±on
Open your web browser and enter
http://²9³.²·¹.².³µ¶
into the
Address
field. Press the
Enter
key and the
Password
screen will appear.
Address Bar
NOTE:
The default IP address is
²9³.²·¹.².³µ¶
.
If the IP address has been changed using DHCP
or via the console interface, enter the assigned
IP address instead of the default.
The first time you open the web-based utility, enter
adm±n (
the default username) in the
User name
field and
enter it again in the
Password
field. Click the
OK
button.
You can change the Access Point’s password later from the
Administration > Management
screen.
Login Screen
Web-Based Utility
The first screen that appears in the web-based utility is the
Setup screen. This allows you to change the Access Point’s
general settings. There are five tabs across the top of
the screen:
Setup
,
W±reless
,
AP Mode
,
Adm±n±strat±on
,
and
Status
. Each tab contains screens that will help you
configure and manage the Access Point.
Setup > Basic Setup
Setup > Basic Setup
Enter names for the Access Point. The host name can be
used to access the Web Utility through the network if DNS
has been set up. The device name is for the benefit of
identifying your Access Point after you log in.
Setup
Host Name
This is the host name assigned to the Access
Point. This host name will be published to your DNS server
if the Access Point is configured to acquire the IP address
through DHCP. In that case, Linksys recommends to follow
the company policy on the host name assignment. The
default name is Linksys.
Dev±ce Name
You may assign any device name to
the Access Point. This name is only used by the Access
Point administrator for identification purposes. Unique,
memorable names are helpful, especially if you are
employing multiple access points on the same network.
The default name is
WAP³00E
.
Network Setup
The selections under this heading allow you to configure
the Access Point’s IP address setting(s).
IP Settings
Stat±c IP Address
Selected by default, this option is used
to assign a static or fixed IP address to the Access Point.
Local IP Address
The IP address must be unique to your
network. The default IP address is
²9³.²·¹.².³µ¶
.
Subnet Mask
The Subnet Mask must be the same as
that set on the LAN that your Access Point is connected
to. The default is
³¶¶.³¶¶.³¶¶.0
.
Default Gateway
Enter the Default Gateway Address,
typically this is the IP address of your router.
•
•
•