Clifford Arrow 2 Owners Guide - Page 11

User-selectable features - you

Get Clifford Arrow 2 PDF manuals and user guides View all Clifford Arrow 2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

User-selectable features Your Arrow II allows you to set many of its features to your own personal preferences. The system comes from the factory with all of its features pre-programmed as noted in the table below. To change any of the settings, use the following procedure. To restore the feature to its factory setting, just repeat the procedure: 1. Select the feature you wish from the table below. Note the number of of flicks. 2. Turn your vehicle's ignition switch to its "ON" position. 3. Immediately flip the valet switch back and forth the number of times noted for the feature you wish to program (to help you count, you will hear a single chirp confirmation each time you flick). a. If noted, perform the "Secondary action." b. If noted, wait for the "Program completion confirmation." 4. Turn the ignition off. Repeat steps 1-4 for any other feature you wish to program. Feature Factory # of setting flicks Secondary action Program completion confirmation Result AutoArming ON 4 - 1 chirp = OFF 2 chirps = ON Change state from ON to OFF or vice-versa AutoArm & Lock OFF 5 - 1 chirp = OFF 2 chirps = ON Change state from OFF to ON or vice-versa Long-Term Chirp Silencing OFF 6 - 1 chirp = ON 2 chirps = OFF Change state from OFF to ON or vice-versa FACT ON 12 - 1 chirp = OFF 2 chirps = ON Change state from ON to OFF or vice-versa Add a new remote to channel 1 - (arm/disarm) 13 Press remote control button I 1 chirp Button I/channel 1 code of the new remote has been memorized Add a new remote to channel 2 (remote - accessory) 14 Press remote control button II 2 chirps Buttons II/channel 2 code of the new remote has been memorized Add a new remote to channel 3 (silent - arm/disarm) Simultaneously press both remote control 15 buttons I+II (or button 3 of the optional ACG remote control) 3 chirps Buttons I+II/channel 3 code of the new remote has been memorized Add a new remote to channel 5 (remote controlled valet - mode) On the optional 12-channel remote, 17 press LevelShift once, then press button 1 (channel 5) 5 chirps Channel 5 code of the new remote control has been memorized Wait 3 seconds for the Erase all channels - 19 2-chirp confirmation before turning the ignition off 2 chirps All remote control codes have been erased; program in new remote controls 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
User-selectable features
Your Arrow II allows you to set many of its features to your own personal preferences.
The system comes from the factory with all of its features pre-programmed as noted
in the table below. To change any of the settings, use the following procedure. To
restore the feature to its factory setting, just repeat the procedure:
1.
Select the feature you wish from the table below. Note the number of of flicks.
2.
Turn your vehicle’s ignition switch to its “ON” position.
3.
Immediately flip the valet switch back and forth the number of times noted for
the feature you wish to program (to help you count, you will hear a single chirp
confirmation each time you flick).
a.
If noted, perform the “Secondary action.”
b. If noted, wait for the “Program completion confirmation.”
4.
Turn the ignition off. Repeat steps 1-4 for any other feature you wish to program.
Feature
Factory
setting
# of
flicks
Secondary action
Program completion
confirmation
Result
AutoArming
ON
4
—
1 chirp = OFF
2 chirps = ON
Change state from ON
to OFF or vice-versa
AutoArm & Lock
OFF
5
—
1 chirp = OFF
2 chirps = ON
Change state from OFF
to ON or vice-versa
Long-Term
Chirp Silencing
OFF
6
—
1 chirp = ON
2 chirps = OFF
Change state from OFF
to ON or vice-versa
FACT
ON
12
—
1 chirp = OFF
2 chirps = ON
Change state from ON
to OFF or vice-versa
Add a new remote to
channel 1
(arm/disarm)
—
13
Press remote control
button I
1 chirp
Button I/channel 1 code
of the new remote has
been memorized
Add a new remote to
channel 2 (remote
accessory)
—
14
Press remote control
button II
2 chirps
Buttons II/channel 2
code of the new remote
has been memorized
Add a new remote to
channel 3 (silent
arm/disarm)
—
15
Simultaneously press
both remote control
buttons I+II (or button
3 of the optional ACG
remote control)
3 chirps
Buttons I+II/channel 3
code of the new remote
has been memorized
Add a new remote to
channel 5 (remote
controlled valet
mode)
—
17
On the optional
12-channel remote,
press LevelShift once,
then press button 1
(channel 5)
5 chirps
Channel 5 code of the
new remote control has
been memorized
Erase all channels
—
19
Wait 3 seconds for the
2-chirp confirmation
before turning the
ignition off
2 chirps
All remote control
codes have been
erased; program in new
remote controls
10