Clifford IntelliGuard 700 Owners Guide - Page 22
Matrix of user-selectable features
View all Clifford IntelliGuard 700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
Matrix of user-selectable features Feature Select Column 1 1st latched Column 2 2nd latched Column 3 3rd latched Column 4 4th latched Column 5 5th latched Row 1 1st momentary Sound 1: on/off info on page 17 Add new remote to channel 1 info on page 8-9 NOTE 1 Test/adjust primary (normal) zone of the Magnetic Resonance Sensor info on page 13 NOTE 6 QuietChirps: on/off info on page 18 NOT USED Row 2 2nd momentary Sound 2: on/off info on page 17 Add new remote to channel 2 info on page 8-9 NOTE 2 Test/adjust secondary (high) zone of the Magnetic Resonance Sensor info on page 13 NOTE 7 Long-term chirp silencing: on/off info on page 17 Channel 4 timer: D 1sec-2.5min (30sec) NOTE 9 Row 3 3rd momentary Sound 3: on/off info on page 17 Add new remote to channel 3 info on page 8-9 NOTE 3 Pulsed/constant ground output upon panic 15-second entry delay: on/off info on page 13 Channel 4 output: pulsed, timed or latched Row 4 4th momentary Sound 4: on/off info on page 17 Add new remote to channel 4 info on page 8-9 NOTE 4 FACT: on/off info on page 15 AutoLock/UnLock: on/off info on page 18 Siren duration: 30/60 seconds info on page 18 Row 5 5th momentary Sound 5: on/off info on page 17 Erase all channels info on page 8-9 NOTE 5 Factory-delayed courtesy lights: on/off Enhanced AutoArming: on/off info on page 13 NOT USED Row 6 6th momentary Sound 6: on/off info on page 17 NOT USED Set a new secret valet code info on page 12 NOTE 8 AutoArm & Lock: on/off info on page 13 NOT USED Gray cells indicate features that require programming by trained Clifford installers. DO NOT change any of these settings. D WARNING: If you have remote window and sunroof closure, DO NOT CHANGE THIS SETTING: it requires installer-only adjustment. Changing the duration may cause damage. NOTE 1: Transmit channel 1 (or other channel of your choosing) of the new remote control. You will hear two chirps to indicate that the code has been accepted and recorded. NOTE 2: Transmit channel 2 (or other channel of your choosing) of the new remote control. You will hear two chirps to indicate that the code has been accepted and recorded. NOTE 3: Transmit channel 3 (or other channel of your choosing) of the new remote control. You will hear two chirps to indicate that the code has been accepted and recorded. NOTE 4: Transmit channel 4 (or other channel of your choosing) of the new remote control. You will hear two chirps to indicate that the code has been accepted and recorded. NOTE 5: When you hear the two chirps, all remote control codes will have been erased from system memory. You must now add the new and/or existing remote controls to the system (i.e., program channels 1-5 of each remote that will be used with your IntelliGuard 700 system). NOTE 6: Turn off the ignition and exit the vehicle. Firmly "thump" the window pillar with the side of your fist. You should hear a chirp to confirm activation of the sensor's main zone. Use remote control button 2 to increase sensitivity, button 4 to decrease it. Higher and higher pitched tones confirm each sensitivity increase, lower and lower tones confirm each decrease. Repeat until the sensor is set to the sensitivity you wish, then press button 1 to record the new sensitivity level and exit sensor test/adjust mode (you'll hear 3 chirps to confirm this). You may now either arm the system with channel 1 or enter the vehicle. NOTE 7: Use the same procedure as NOTE 7, but strike the window pillar lightly. NOTE 8: Immediately flip the switch to its latched position, then enter the new code that you wish to use. Make sure to return the switch to its center position when complete, then wait 3 seconds (you will hear two chirps when the system has accepted the new code). Turn the ignition off. VERY IMPORTANT: You must immediately test your new secret disarming/valet code: Turn the ignition on, enter your new code, then flip the switch to its latched position. The LED will illuminate. If it does not, the new code you programmed and the one you just entered do not match. The system has reverted to the previous code. NOTE 9: The timer starts as soon as you enable this feature. When the duration you wish has been reached, press button 1 on the remote control. You will hear two chirps to confirm the new duration. 21 22