Cobra 29 LX BT Operating Instructions - Page 14
Ready For, Pairing, Pw 0000 - features
View all Cobra 29 LX BT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
Operation Operation Setting Contrast Mode Note If an attempt is made to exceed the highest or lowest contrast levels, 1 error beep will be heard. Setting Contrast Mode Press Menu/Enter knob and rotate clockwise to select Set Contrast. Press Menu/Enter knob again and rotate clockwise to increase contrast, counter-clockwise to decrease contrast. Press Menu/Enter knob to set contrast. TURN CH KNOB TO SET CONTRAST III. Successful pairing will be indicated by a tone to confirm entry to Connected mode. A pair record will also be established for subsequent connections. B. Subsequent pairings with a cell phone: I. Follow any cell phone manufacturer instructions if needed, to enable the Bluetooth function. II. Successful pairing will be indicated by a tone to confirm entry to Connected mode. Press Menu/Enter knob again to exit routine. To Answer Calls Bluetooth® Note When cell phone calls are in progress using the Bluetooth Bluetooth® Calls on a Bluetooth enabled cell phone can be routed through the 29 LX BT speaker or external speaker accessory. 1 Press and release the BT Button when the cell phone ring is heard through the 29 LX BT speaker. 2 Speak into the 29 LX BT microphone. The CB function of the unit and PTT Button will be disabled while a call is in progress. NBA/NALNfueLnaittSuaWrreRes,d1t.i5hsaebC2leBdf.u3nctionCsAoLf the TX READY FOR S/RF RF RX PAIRING PW 0000 SWRNote CALDuaSlIPGoi1nt Bl3uet5oo7 t9h+: 30dB Two cell phones can be pairedMEN U PU SH E N T E R BT MEM Button WX ! OL aSnQd and useDdYNfoArMteIKaEm drivers. RF GAIN Note DELTA TUNE SCAN MEM SCAN CB / WX T BACK CH 9/ 3 Press and release of the BT Button to end the 19 call. A tone will sound. To Initiate Calls DIM 1 Dial a number according to the cell phone manu- ESC facturer's instructions. The key press and other tones will be heard through the 29 LX BT speaker. SWR CAL 2 Press Send on the cell phone send key a few seconds, you will hear the ring tone for the number you dialed on the CB speaker. If no further pairing steps are taken, the unit will time-out and retuMrnINto Standby after five minutes. During the pairing process, press and release the BT Button to cancel the pairing process. To Pair with a Cell Phone With 29 LX BT MpIoNwer On,MpArXess and hold theOBFTF Button for six seconds to enter Standby mode. A tone will sound to confirm entry to Standby. A. First time pairing with a cell phone: I. A tone will sound to confirm Pairing mode. II. Follow the cell phone manufacturer's Once connected, speak into the microphone. 3 Press and release of the BT Button to end the 4 call. A tone will sound. Press and hold the BT Button for two seconds to 5 redial a number. A tone will sound; and after a few seconds, you will hear the ring tone for the number you dialed. Note For Text-to-Speech conversion, an app should be downloaded instruction to enable its Bluetooth function and enter the PIN (Personal Identification Number) 0000. To Enable or Disable Voice Dialing If the paired cell phone supports voice dialing, press and release the BT Button twice to toggle to your cell phone. between enabling and disabling this feature. Note When cell phone calls are in progress using the Bluetooth features, the CB functions of the unit are disabled until the phone call is put on hold (see page 24). Note The external microphone (see accessories on page 35) can be plugged into the rear of the unit and clipped to a pocket or lapel for hands-free speech during calls. When the microphone is plugged in, the main microphone will not pick up speech during calls but will be fully functional for CB operation. 22 23