Craftsman 11177 Operation Manual - Page 10

Paper, Clamp, Lever, Adhesive, Sandpaper, Cushion, Paperpunch

Page 10 highlights

PAPER CLAMP LEVER CUSHION NON-ADHESIVE SANDPAPER Fig. 2 [] Wrap sandpaper around cushion. Lift lever on opposite end of sander and insert loose end of sandpaper under the paper clamp. Fit sandpaper against cushion as tight as possible. [] Lift up on paper clamp lever and lock into place. INSTALLING ADHESIVE SANDPAPER See Figure 3. [] Unplug the sander. [] If replacing adhesive sandpaper, remove old sandpaper by peeling it off cushion. If replacing regular sandpaper, release paper clamp by lifting up on paper clamp lever and disengaging it from the tab on the cushion. [] Remove non-adhesive sandpaper, then lift up on paper clamp lever and lock it into place. [] Carefully peel adhesive backing from new 1/4 sheet sandpaper. [] Position sandpaper, making sure front edge of sandpaper is aligned with front edge of the cushion, then carefully press sticky side of sandpaper on cushion. NOTE: Sandpaper must be aligned with the front edge of the cushion for proper functioning of the flush sanding feature. The cushion on the sander is approximately 1/4 in. smaller than precut adhesive-backed sanding sheets. If desired you may want to trim off the overhang of sandpaper on the back side of cushion. The cushion has been made smaller so that multiple sheets of nonadhesive sandpaper can be installed. PAPER PUNCH See Figure 4. A paper punch template has been supplied with the sander. It should be used for aligning and punching holes in the sandpaper for alignment with the holes in the cushion. CUSHION iCON i PAPER CLAMP LEVER ADHESIVE SANDPAPER PAPERPUNCH Fig. 3 Fig. 4 Punching the holes properly is a necessary step in order for the dustless feature of the sander to function properly. [] Install sandpaper on the sander. [] Align sander cushion to paper punch as shown by the icon on the paper punch template. [] Push down on sander. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

PAPER
CLAMP
LEVER
CUSHION
NON-ADHESIVE
SANDPAPER
Fig. 2
[]
Wrap sandpaper
around
cushion.
Lift lever on opposite
end of sander and insert loose end of sandpaper
under
the paper clamp.
Fit sandpaper
against
cushion as
tight as possible.
[]
Lift up on paper clamp
lever and lock into place.
INSTALLING
ADHESIVE
SANDPAPER
See Figure 3.
[]
Unplug the sander.
[]
If replacing
adhesive sandpaper,
remove old sandpaper
by peeling it off cushion.
If replacing
regular sandpaper,
release paper clamp by lifting up on paper clamp lever
and disengaging
it from the tab on the cushion.
PAPER
CLAMP
LEVER
ADHESIVE
SANDPAPER
Fig. 3
[]
Remove non-adhesive
sandpaper,
then lift up on paper
clamp lever and lock it into place.
[]
Carefully
peel adhesive
backing
from new 1/4 sheet
sandpaper.
[]
Position sandpaper,
making sure front edge of sand-
paper is aligned with front edge of the cushion, then
carefully
press sticky side of sandpaper
on cushion.
NOTE:
Sandpaper
must be aligned with the front edge
of the cushion
for proper functioning
of the flush sand-
ing feature.
The cushion
on the sander is approximately
1/4 in.
smaller than precut adhesive-backed
sanding sheets.
If desired you may want to trim off the overhang of
sandpaper
on the back side of cushion. The cushion
has been made smaller so that multiple sheets of non-
adhesive sandpaper
can be installed.
PAPER
PUNCH
See Figure 4.
A paper punch template
has been supplied
with the sand-
er. It should be used for aligning
and punching
holes in the
sandpaper
for alignment
with the holes in the cushion.
CUSHION
iCON
i
PAPERPUNCH
Fig. 4
Punching the holes properly is a necessary
step in order
for the dustless feature of the sander to function
properly.
[]
Install sandpaper
on the sander.
[]
Align sander cushion to paper punch as shown by the
icon on the paper punch template.
[]
Push down on sander.
10