Cub Cadet 945 SWE Two-Stage Snow Thrower 945 SWE Operator's Manual
Cub Cadet 945 SWE Two-Stage Snow Thrower Manual
 |
View all Cub Cadet 945 SWE Two-Stage Snow Thrower manuals
Add to My Manuals
Save this manual to your list of manuals |
Cub Cadet 945 SWE Two-Stage Snow Thrower manual content summary:
- Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 1
Troubleshooting • Warranty Operator's Manual Two Stage Snow Thrower - Model 945 SWE WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Printed In USA CUB CADET - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 2
To The Owner 1 Thank You Thank you for purchasing a Snow Thrower manufactured by Cub Cadet LLC. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 3
instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 4
parts can amputate hands and feet. 2. The auger/impeller control lever is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may cause personal injury. unclogging. 19. Use only attachments and accessories approved by the manufacturer (e.g. wheel weights, tire chains - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 5
to clear snow from machine and prevent freeze up of auger/impeller. 10. Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer etc. 11. Always refer to the operator's manual for proper instructions on off - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 6
SURFACE Engine parts, especially the muffler, become extremely hot during operation. Allow engine and muffler to cool before touching. WARNING! Your Responsibility-Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 7
snow thrower is from the operating position only. Exceptions, if any, will be specified. IMPORTANT: This unit is shipped with the engine full of oil. After assembly, refer to the separate Engine Owner's Manual Figure 3-11. 5. Secure the upper handle, support tubes and lower handle with the two wing - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 8
4. Check that the chute cables are properly routed through the cable guide attached to the lower handle assembly. See Figure 3-6. A B Figure shear pins and bow tie cotter pins have been included with your snow thrower. There are holes provided in the plastic dash panel for convenient storage - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 9
NOT be tight. Refer to Figure 3-10. 1. In a well-ventilated area, start the snow thrower engine as instructed in the engine operator's manual. 2. While standing in the operator's position (behind the snow thrower), engage the auger. 3. Allow the auger to remain engaged for approximately ten (10 - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 10
refer to the instructions for Adjusting Drive and Auger Controls later in this section. Testing Drive Control & Shift Lever 1. With the engine turned off, move the shift lever into sixth (6) position. Refer to Figure 3-10. 2. With the wheel drive control released, push the snow thrower forward, then - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 11
on all engine controls, refer to the separate Engine Operator's Manual supplied with this unit. Speed Selector Shift Lever The speed selector . Augers When engaged, the augers rotate and draw snow into the auger housing. Chute Assembly Snow drawn into the auger housing is discharged out the - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 12
Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop. Two-Way Chute Control™ The two that you can operate the chute directional control without interrupting the snow throwing process. If the auger control is engaged simultaneously with the - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 13
parts have stopped before unclogging. The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow Drive Control. 2. Stop the engine as instructed in the engine operator's manual included with the snow thrower. 3. Remove the clean-out tool from - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 14
Engine Refer to the Engine Operator's Manual packed with your snow thrower for instructions on starting and stopping the engine. To Part No. 738-04155 replacement shear pins. Any damage to the auger gearbox or other components as a result of failing to do so will NOT be covered by your snow thrower - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 15
any adjustments or repairs. Engine Refer to the Engine Operators Manual Maintenance section included with the snow thrower. Lubrication Drive and Shifting Mechanism At least once a season or after every 25 hours of operation, remove rear cover. Lubricate all chains, sprockets, gears, bearings - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 16
shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and Chute Control The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to the Operation section for instructions. The remote chute control - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 17
Refer to the Adjustment section of the Assembly & Set-Up section earlier in this manual for instructions on how to adjust the wheel drive control. To further check the adjustment, proceed as follows: 1. With the snow thrower tipped forward (be certain to run the fuel tank dry before tipping the unit - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 18
washer. Refer to Figure 7-1. Remove Loosen Figure 7-3 Auger Belt Replacement Figure 7-1 To remove and replace your snow thrower's auger belt, proceed 2. Remove the hex screws and lock nuts securing the forward as follows: end of the support tubes to the back of the auger housing, 1. Remove - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 19
2. Slip the auger control belt (the front belt) off the engine pulley. 3. Pull the brake bracket assembly towards the cable guide roller and unhook the auger cable "Z" fitting. Refer to Figure 7-5. 6. Block the secure the auger pulley assembly on the input shaft. Figure 7-6 Section 7 - Service 19 - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 20
in (towards idler) to increase tension on belt, or out to decrease belt tension. NOTE: The brake puck must always be snow thrower. Drive Belt Replacement If not already done, remove the auger drive belt from the front pulley of the engine double pulley. Refer to "Auger Belt Replacement" instructions - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 21
the friction wheel assembly. Figure 7-11 NOTE: If the sprocket fell from the snow thrower chain while 8. Reassemble the new friction wheel onto the hub assembly, removing the hex shaft the self-tapping screws. Pivot the snow thrower down to its normal operating position. Section 7 - Service 21 - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 22
Troubleshooting 8 Problem Excessive vibration Cause 1. Loose parts or damaged auger. Loss of power 1. Spark plug wire loose. 2. Gas cap vent hole plugged. Unit fails to propel itself 1. Drive control cable in need of adjustment. Unit fails to discharge snow 2. Drive belt loose or damaged. - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 23
Parts Component 9 Part Number and Description 929-0071A Extension Cord, 110V 954-04194A 954-04202 Auger Drive Belt Wheel Drive Belt (4282) to order replacement parts or a complete Parts Manual (have your full model number and serial number ready). Parts Manual downloads are also available free - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 24
10 The following attachments and accessories are available for your Cub Cadet 945 series snow thrower. See your Cub Cadet dealer or the retailer from which you purchased your snow thrower for information regarding price and availability. Model Number Description 490-241-0013 OEM-390-674 OEM-731 - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 25
Notes 25 - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 26
small off-road engine or part has failed due to abuse, neglect, improper maintenance or unapproved modifications. You are responsible for presenting your small off-road engine to an Authorized MTD Service Dealer as soon as a problem exists. The warranted repairs should be completed in a reasonable - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 27
parts sufficient to meet the expected demand for such parts. (9) Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner start enrichment system (soft choke) • Carburetor and internal parts • Fuel Pump • Fuel Tank (2) - Cub Cadet 945 SWE Two-Stage Snow Thrower | 945 SWE Operator's Manual - Page 28
as: belts, skid shoes, shave plates and tires. HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE, through your local authorized service dealer. To locate the dealer in your area: In the U.S.A. To locate the dealer in your area, check your Yellow Pages, or contact Cub Cadet
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
 |
 |
Printed In USA
Safe Operation Practices • Set-Up • Operation •
Maintenance • Service • Troubleshooting •
Warranty
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
O
PERATOR
’
S
M
ANUAL
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
FORM NO. 769-08125
(April 30, 2012)
Two Stage Snow Thrower — Model 945 SWE