D-Link DCS-5300W Product Manual - Page 106

Apply and Erase Buttons, Motion Detection, Schedule in event mode

Get D-Link DCS-5300W - Network Camera PDF manuals and user guides
UPC - 790069263248
View all D-Link DCS-5300W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

Using IP surveillance Software (continued) Scheduling (continued) Apply and Erase Buttons After you have selected the time period with "Begin time" and "End time" picker, you can apply the period picker, shown in the figure below, to set the periodical types of the time interval set previously. After the settings in "Begin Time", "End Time" and "Period Picker" are all done, you should click the "Apply" button or "Erase" button to add or clear this scheduling information to the editing schedule scheme. Note that only after you click on the "Apply" button, the scheduling information settings will be written back into the whole editing schedule scheme. That means this edited scheduling time interval is valid only after you "Apply" the changes. Period picker Apply Erase Schedule in event mode You can select to record in Event mode or Continuous mode by the Schedule mode selector as shown in the figure below. There are two types of event recording. Please refer to the following two sections for more information. Motion Detection As shown above, you can check the windows that you would like to record while the motion detection is triggered. 106

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
106
Using IP surveillance Software (continued)
Scheduling (continued)
Apply and Erase Buttons
After you have selected the time period with “Begin time” and “End time” picker,
you can apply the period picker, shown in the figure below, to set the periodical
types of the time interval set previously. After the settings in “Begin Time”, “End
Time” and “Period Picker” are all done, you should click the “Apply” button or
“Erase” button to add or clear this scheduling information to the editing schedule
scheme. Note that only after you click on the “Apply” button, the scheduling
information settings will be written back into the whole editing schedule scheme.
That means this edited scheduling time interval is valid only after you “Apply”
the changes.
Period picker
Apply
Erase
Schedule in event mode
You can select to record in Event mode or Continuous mode by the Schedule
mode selector as shown in the figure below. There are two types of event
recording. Please refer to the following two sections for more information.
Motion Detection
As shown above, you can check the windows that you would like to record
while the motion detection is triggered
.