D-Link DCS-5300W Product Manual - Page 87

Modulation Mode, DCS-5300W, DCS-2000, Display Options, Connection Time Day:Hour:Min - dcs no signal

Get D-Link DCS-5300W - Network Camera PDF manuals and user guides
UPC - 790069263248
View all D-Link DCS-5300W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

Using IP surveillance Software (continued) Monitor Program (continued) Modulation Mode You must select the input signal format (NTSC or PAL) for displaying the original resolution of video stream from DCS5300W. NOTE: You need to select the input signal format according to the camera type or CCD module type that is connected to the DCS-5300W. Due to the nature of CMOS sensors (for the DCS-2000 and DCS-2100+), the input signal format needs to be set to PAL regardless whether the power line frequency connected is 50 or 60 Hz. Display Options: In the video displaying frame of each channel, there are two status bars. The upper bar contains "Camera location" and "time of the remote site." The lower bar contains "Connection time" and "Recording time." All of them, shown in the figure below, can be enabled or disabled here individually for the status indication. Apply to full screen mode can also be turned on here. Once it has been checked, the status bar in each channel showing date, location, connection, and recording time will be shown in both display frame mode and full screen mode. Location (channel number + Camera Name) Remote Time Connection Time (Day:Hour:Min) 0 day 00:01 Recording Time (Day:Hour:Min) 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
87
Using IP surveillance Software (continued)
Modulation Mode
You must select the input signal format (NTSC or PAL) for
displaying the original resolution of video stream from
DCS-
5300W
.
±
NOTE: You need to select the input signal format according to the camera
type or CCD module type that is connected to the
DCS-5300W
. Due to the
nature of CMOS sensors (for the
DCS-2000
and
DCS-2100+
), the input signal
format needs to be set to PAL regardless whether the power line frequency
connected is 50 or 60 Hz.
Display Options:
In the video displaying frame of each channel, there are two status bars. The
upper bar contains “Camera location” and “time of the remote site.” The lower
bar contains “Connection time” and “Recording time.” All of them, shown in the
figure below, can be enabled or disabled here individually
for the status indication.
Apply to full screen mode can also be turned on here. Once it has been checked,
the status bar in each channel showing date, location, connection, and recording
time will be shown in both display frame mode and full screen mode.
0 day
00:01
Location (channel number + Camera Name)
Remote Time
Connection Time (Day:Hour:Min)
Recording Time (Day:Hour:Min)
Monitor Program (continued)