D-Link DSL-2640B Product Manual

D-Link DSL-2640B - ADSL2/2+ Modem With Wireless Router Manual

Get D-Link DSL-2640B - ADSL2/2+ Modem With Wireless Router PDF manuals and user guides
UPC - 790069298288
View all D-Link DSL-2640B manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DSL-2640B manual content summary:

  • D-Link DSL-2640B | Product Manual - Page 1
  • D-Link DSL-2640B | Product Manual - Page 2
    --Static Route 47 Routing--Default Gateway 48 RIP 49 Quality of Service 50 Port Mapping 52 Certificate 54 Local 54 Trusted CA 56 Wireless 57 Wireless--Advanced 58 Wireless--MAC Filter 60 Wireless--Bridge 61 Wireless--QoS 62 Tools 63 D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 
  • D-Link DSL-2640B | Product Manual - Page 3
    82 Troubleshooting 83 Wireless Basics 85 What is Wireless 86 Tips 88 Wireless Modes 89 Networking Basics 90 Check your IP address 90 Check your MAC address 90 Statically Assign an IP address 91 Contacting Technical Support 92 Warranty 93 Registration 95 D-Link DSL-2640B ADSL2+ 4-Port
  • D-Link DSL-2640B | Product Manual - Page 4
    in a single device. The DSL-2640B also has four addional 10/100Mbps ethernet ports to connect non-wireless computers. This user manual provides you with a simple and easy-to-understand format to install and configure your router. Package Contents • ADSL2/2+ 4-Port Wireless Router • 12VDC, 1A DC
  • D-Link DSL-2640B | Product Manual - Page 5
    the wireless is operational. A flashing green light indicates wireless traffic is passing through the router. Local Network LEDs A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission. D-Link DSL-2640B ADSL2+ 4-Port Router User
  • D-Link DSL-2640B | Product Manual - Page 6
    use by D-Link service personnel for maintenance purposes only. ON/OFF Press this button to turn the unit on or off. LAN Ports (1-4) Connect Reset Pressing the Reset button for 5 seconds restores the router to its original factory default settings. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual
  • D-Link DSL-2640B | Product Manual - Page 7
    cable to a hub or a switch and the other to the Ethernet port (labeled LAN) on the router. Note that either a crossover or straight-through Ethernet cable can be used. The router automatically recognizes the type of connection that is required. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 
  • D-Link DSL-2640B | Product Manual - Page 8
    power strip. Then turn on and boot up your PC and any LAN devices, such as hubs or switches, and any computers connected to them. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 
  • D-Link DSL-2640B | Product Manual - Page 9
    (TCP/IP) does not appear as an installed component, then click on Install. 5. In the Select Network Component Type window, click on protocol and then the Add button. 6. Select Internet Protocol (TCP/IP) from the list and then click on OK. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 
  • D-Link DSL-2640B | Product Manual - Page 10
    Use the following IP address and type 192.168.1.x (where x is any number between 2 and 254) for the IP address field and 255.255.255.0 for the Subnet Mask field. 5. Click on OK twice to save your changes and then close the Control Panel. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 10
  • D-Link DSL-2640B | Product Manual - Page 11
    purposes (username / password: support / support). Note: Passwords can be changed at any time. 3. Enter your user name and password, and then click OK to display the user interface. Note: This manual has been prepared using the admin user name. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 11
  • D-Link DSL-2640B | Product Manual - Page 12
    process, click on the box labeled DSL Auto-connect, a process that will automatically detect the first usable PVC and automatically detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server available). To continue, click on the Next button. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 12
  • D-Link DSL-2640B | Product Manual - Page 13
    5 - Home If you uncheck the DSL Auto-connect box, more options will appear below the check box. Enter the VPI/VCI values as indicated by your ISP. There is also an option to enable Quality of Service. When you are ready, click Next to continue. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 13
  • D-Link DSL-2640B | Product Manual - Page 14
    modes except PPPoA over ATM and IP over ATM). Select this option if required by your ISP. The following is a PPPoA example. Click Next to continue. Select an appropriate network protocol and encapsulation mode. Click Next to continue. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 14
  • D-Link DSL-2640B | Product Manual - Page 15
    Section 5 - Home Enter the PPP username and password given to you by your ISP. Then decide if you will be using any features such as dial on demand, PPP IP extension, keep alive and then click Next. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 15
  • D-Link DSL-2640B | Product Manual - Page 16
    Section 5 - Home The next step is to configure the Network Address Translation (NAT) settings. For the example, NAT will be enabled. Leave the remaining fields at their defaults and click Next to continue. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 16
  • D-Link DSL-2640B | Product Manual - Page 17
    assign IP addresses, then enable the DHCP server and enter the range of IP addresses that the DHCP server can assign to your computers. Disable the DHCP server if you would like to manually assign IP addresses. Click Next to continue. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 17
  • D-Link DSL-2640B | Product Manual - Page 18
    your router. If you enable wireless, be sure to enter a wireless network name (SSID) to identify your wireless connection. You will need to know the wireless network name (SSID) to connect any wireless computers on your network to your router. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 18
  • D-Link DSL-2640B | Product Manual - Page 19
    are complete, the WAN Setup Summary screen displays all WAN settings that you have made. Check that the settings are correct before clicking on the Save / Reboot button. Clicking on Save / Reboot will save your settings and restart your router. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 19
  • D-Link DSL-2640B | Product Manual - Page 20
    on using the wireless, make sure you have entered a wireless network name in the (SSID) field and have selected your country from the drop-down list. Click Apply to save your changes. Click Security to proceed to the wireless security section. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 20
  • D-Link DSL-2640B | Product Manual - Page 21
    configuration. Network authentication methods include the following: Open: Anyone can access the network. The default is a disabled WEP encryption setting. uses AES encryption and requires you to enter a password and an re-key interval time. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 21
  • D-Link DSL-2640B | Product Manual - Page 22
    upgrades in the enterprise environment, this mixed authentication method allows "upgraded" WPA2/WPA: users and users not yet "upgraded" to access the network via the router. RADIUS server information time. Both TKIP and AES are also used. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 22
  • D-Link DSL-2640B | Product Manual - Page 23
    want to add a new connection for the WAN interface and to proceed to the ATM PVC Configuration screen as seen on page 25. The ATM PVC Configuration screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a service category. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 23
  • D-Link DSL-2640B | Product Manual - Page 24
    -time Used by time-sensitive applications such as real-time video. Rt-VBR service allows the network more Variable Bit Rate): flexibility than CBR. Quality of Can be enabled only for UBR without PCR, UBR with PCR, and Non Realtime VPR. Service: D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 24
  • D-Link DSL-2640B | Product Manual - Page 25
    , click on the Enable 802.1q checkbox and then enter the VLAN ID number. When finished with your selections, click Next to continue. Note: These settings are ISP dependant. For information regarding proper configuration, contact your ISP. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 25
  • D-Link DSL-2640B | Product Manual - Page 26
    Internet. If selected, you will be asked to enter the static IP address. Note: These settings are ISP dependant. For information regarding proper configuration, contact your ISP. When finished, click Next to proceed to the NAT Settings screen. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 26
  • D-Link DSL-2640B | Product Manual - Page 27
    WAN service and then set the Service Name. When finished, click the Next button and the following WAN summary screen will be displayed. This screen will outline all WAN settings for review. When satisfied with the settings click the Apply button. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual
  • D-Link DSL-2640B | Product Manual - Page 28
    button to save the changes and reboot the router. When the router restarts the DSL Router Reboot screen will appear during the reboot process. Close the DSL Configuration window and wait at least two minutes before reopening your web browser. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 28
  • D-Link DSL-2640B | Product Manual - Page 29
    to manually assign IP addresses. The Save button only saves the LAN configuration data, but does not apply the configuration. Select the Save/Reboot button to save the LAN configuration data, reboot the router and apply the new configuration. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 29
  • D-Link DSL-2640B | Product Manual - Page 30
    Section 5 - Home DNS DNS Server Configuration Use the DNS Server screen to request automatic assignment of a DNS or to specify a primary and ). Enter one primary and one secondary DNS address in each field. Click Apply to save the configuration. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 30
  • D-Link DSL-2640B | Product Manual - Page 31
    (DynDNS.org or TZO), from which you have obtained a dynamic DNS address. Enter the hostname and the interface that you are using. Also enter the username and password assigned by the DNS service. Click on Apply to save these configurations. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 31
  • D-Link DSL-2640B | Product Manual - Page 32
    Section 5 - Home Logout To log out of the router's user interface at any time during the setup, click on the Logout button. A confirmation screen will appear confirming that you really want to log out. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 32
  • D-Link DSL-2640B | Product Manual - Page 33
    . ADSL The ADSL settings page contains modulation and capability settings. Consult your ISP to determine the correct settings. Click Apply if you are finished or click on Advanced Settings if you want to configure more advanced settings. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 33
  • D-Link DSL-2640B | Product Manual - Page 34
    Settings The test mode can be selected from the ADSL Advanced Settings page. Test modes include normal, reverb, medley, no retrain, and L3. After you make your selection, click on Apply to save these settings first before you go to Tone Selection. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual
  • D-Link DSL-2640B | Product Manual - Page 35
    Section 6 - Advanced Setup ADSL Tone Settings The frequency band of ADSL is split into 256 separate tones, each spaced 4.3125 kHz 0 to 31 for upstream and from 32 to 255 for downstream. Do not change these settings unless directed by your ISP. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 35
  • D-Link DSL-2640B | Product Manual - Page 36
    software that requires communication with the Internet (e.g. peer-to-peer, games, etc.). This figure shows the Virtual Servers Setup page that allows you to configure your virtual server(s). Click on the Add button to configure a virtual server. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 36
  • D-Link DSL-2640B | Product Manual - Page 37
    be the IP address of the computer on your network which is using the application or game. To determine your IP address see Networking Basics in the Appendix section of this manual. Once you are satisfied with your selection, click Apply once. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 37
  • D-Link DSL-2640B | Product Manual - Page 38
    Setup The following screen appears after you save your selection. To add additional virtual servers, click on the Add button. If you need to remove any of the server names, select its check box in the Remove column and click on the Remove button. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual
  • D-Link DSL-2640B | Product Manual - Page 39
    Section 6 - Advanced Setup DMZ You can define the IP address of the DMZ Host on this screen. The DMZ is used to forward all IP packets coming into the router to a specified IP address. Enter the IP address and click Apply. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 39
  • D-Link DSL-2640B | Product Manual - Page 40
    buttons to configure the inbound and outbound filters. Incoming IP Filtering Setup An Incoming IP filter allows you to specify which WAN traffic is allowed to pass through the firewall. Click on the Add button to add incoming filter settings. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 40
  • D-Link DSL-2640B | Product Manual - Page 41
    Section 6 - Advanced Setup This next screen will appear when you click Add. Enter the filter name, select the Protocol, enter source Make sure at least one or multiple WAN interfaces are selected to apply the rule. Click Apply to save. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 41
  • D-Link DSL-2640B | Product Manual - Page 42
    the "Remove" column and click Remove. Outgoing IP Filtering Setup An Outgoing IP filter allows you to specify which LAN traffic is blocked from passing through to the WAN side (Internet). Click on the Add button to add outgoing filter settings. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 42
  • D-Link DSL-2640B | Product Manual - Page 43
    the IP filter. The screen lists the IP filters that were added from the previous screen. To add another filter click Add. To remove any previously created filter, place a checkmark next to the filter in the "Remove" column and click Remove. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 43
  • D-Link DSL-2640B | Product Manual - Page 44
    any specified rules. If you click Change Policy, a confirmation dialog allows you to verify your change. Select Yes to continue, or No to to cancel. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 44
  • D-Link DSL-2640B | Product Manual - Page 45
    , the necessary Frame Direction, and WAN interface (bridge mode only). Click Apply to save. After you save the settings, a screen showing the settings will appear. On this screen you will be able to add, view and delete MAC filtering rules. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 45
  • D-Link DSL-2640B | Product Manual - Page 46
    Section 6 - Advanced Setup Parental Control Time of Day Restrictions In a home setting, parents can disallow access to the router (and see "Networking Basics" in the Appendix section of this manual. Click Apply to save the settings and continue. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 46
  • D-Link DSL-2640B | Product Manual - Page 47
    table (a maximum of 32 entries can be configured). To proceed, click on Add. On the Static Route Add page, enter the destination network address, subnet mask, gateway IP address, and select an available WAN interface. When complete, click Apply. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 47
  • D-Link DSL-2640B | Product Manual - Page 48
    a gateway address. This shows the Default Gateway screen when the Enable Automatic Assigned Default Gateway is unchecked. Enter a gateway IP in the Use Default Gateway IP Address field and/or select a WAN Interface. When ready, click Apply. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 48
  • D-Link DSL-2640B | Product Manual - Page 49
    If RIP is set to active, the router will advertise its routes (reachability information) to others; if RIP is set to passive, the router will not advertise its routes, but will listen and update its routes based on other routers' advertisements. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 49
  • D-Link DSL-2640B | Product Manual - Page 50
    sensitive data (e.g. video streaming) is given priority over other non-essential data. You can configure the Quality of Service to apply different priorities to traffic on the router. Click Add to view the Add Network Traffic Class Rule screen. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 50
  • D-Link DSL-2640B | Product Manual - Page 51
    Advanced Setup This screen allows you to add a network traffic class rule. A rule consists of a traffic class name and at least one condition. All configured conditions must first be met before the rule takes effect. Click Apply to save any changes. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual
  • D-Link DSL-2640B | Product Manual - Page 52
    Section 6 - Advanced Setup Port Mapping Port mapping is a feature that allows you to open ports to allow certain Internet applications on the WAN side to pass through the the remove column next to the desired group and click the Remove button. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 52
  • D-Link DSL-2640B | Product Manual - Page 53
    Section 6 - Advanced Setup After clicking the Add button, the Port Mapping Configuration screen appears, allowing you to IP address from the local DHCP server. These clients may obtain public IP addresses from your ISP. Click Apply when finished. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual
  • D-Link DSL-2640B | Product Manual - Page 54
    Section 6 - Advanced Setup Certificate Certificates are used Click the Local Cert. button to configure your Local Certificates. Click the Trused CA button to configure your Trusted CA Certificates. Local A local Import Certificate to retrieve it. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 54
  • D-Link DSL-2640B | Product Manual - Page 55
    Section 6 - Advanced Setup If you selected Create Certificate Request the Create New Certificate Request screen will appear. Enter the following into the Private Key field. Click Apply to submit the request to import the certificate. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 55
  • D-Link DSL-2640B | Product Manual - Page 56
    Section 6 - Advanced Setup Trusted CA The trusted certificate authority (CA) allows you to verify the certificates of your peers. Note that you . Paste the content of the certificate that you wish to add in the Certificate field and click Apply. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 56
  • D-Link DSL-2640B | Product Manual - Page 57
    System). WDS allows your wireless network to be expanded using multiple access points without the need for wired connections between the APs. The Wireless -- QoS section allows you to configure the wireless quality of service for the router. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 57
  • D-Link DSL-2640B | Product Manual - Page 58
    readiness. A beacon interval is a period of time (sent with the beacon) before sending the beacon again. The beacon interval may be adjusted in milliseconds (ms). D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 58
  • D-Link DSL-2640B | Product Manual - Page 59
    - Advanced Setup Xpress A wireless clients. High network traffic areas should select Short preamble type. Transmit Power: This is the percentage of power that should be transmitted from your wireless router. Select from 20%, 40%, 60%, 80%, and 100%. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual
  • D-Link DSL-2640B | Product Manual - Page 60
    Section 6 - Advanced Setup Wireless--MAC Filter The MAC Filter feature allows you to disable, allow or deny users access to the wireless router based on their MAC address. To add see "Networking Basics" in the Appendix section of this manual. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 60
  • D-Link DSL-2640B | Product Manual - Page 61
    set to Enabled or Bridges MAC Enabled(scan) only those bridges whose Address: MAC addresses appear in these fields will be granted access. Click Refresh to update the Remote Bridges MAC Address fields. Click Save/Apply to save the wireless bridge options. D-Link DSL-2640B ADSL2+ 4-Port Router User
  • D-Link DSL-2640B | Product Manual - Page 62
    a QoS entry, click the Add QoS Entry button to proceed to add or remove traffic class rules for your network. Click on Save/Apply WME Settings. See the "QoS" section on page 51 for more information. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 62
  • D-Link DSL-2640B | Product Manual - Page 63
    the Admin button to change the routers account passwords. Click the Services button to configure what services are allowed to pass through the router. Click the IP Address button to define who is permitted access to local management features. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 63
  • D-Link DSL-2640B | Product Manual - Page 64
    monitoring network devices. Telnet: A standard Internet protocol for accessing remote systems. TFTP: (Trivial File Transfer Protocol) A very simple form of the File Transfer Protocol (FTP). D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 64
  • D-Link DSL-2640B | Product Manual - Page 65
    the correct username and password is supplied at log on. Enter the IP address of the management station permitted to access the local configuration and click Apply. This will return you to the previous screen where you can enable access control. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 65
  • D-Link DSL-2640B | Product Manual - Page 66
    synchronize with Internet time servers checkbox. Addional time settings will appear below the checkbox. Select from the list of NTP (Network Time Protocol) time servers.Then select the time zone that you are in and click Apply to save. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 66
  • D-Link DSL-2640B | Product Manual - Page 67
    Status section (see screen on right). To return to the previous screen to configure system log, remember to click on the Tools tab (located on top row) selected log level will be logged and displayed. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual System log when log is disabled. System log when
  • D-Link DSL-2640B | Product Manual - Page 68
    will be sent to a specified IP address and UDP port of a remote system log server. If the selected mode is "Local" or "Both", events will be recorded and viewed locally. Select the desired values and click Apply to save the system log options. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 68
  • D-Link DSL-2640B | Product Manual - Page 69
    if supported), or any service providing Auto-Configuration Servers (ACS) If you wish to enable this protocol, then select enable. Contact your ISP to determine the ACS URL, ACS User Name, and ACS Password. You must click on the Save/Reboot button for the change to take place. D-Link DSL-2640B ADSL2
  • D-Link DSL-2640B | Product Manual - Page 70
    configuration on the router, but would like to revert to a previous configuration. To save your current configuration, click the Backup Settings button. The following pop-up screen will appear with a prompt to open or save the file to your computer. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual
  • D-Link DSL-2640B | Product Manual - Page 71
    settings and restore the router to factory default settings. Click on the Restore Default Settings button to proceed. The following confirmation dialog will appear confirming your decision to restore default settings. Click on OK to continue. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual
  • D-Link DSL-2640B | Product Manual - Page 72
    upgrade. 1. Obtain an updated software image file (firmware) from your ISP. 2. Enter the path of the image file location or click the Browse button to locate the image file. 3. Click the Update Software button once to upload the new image file. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 72
  • D-Link DSL-2640B | Product Manual - Page 73
    Connection to your Internet service provider There are three buttons at the bottom of the page; Next Connection (appears only if you have created more than one connection), Test and Test with OAM F4 (which will allow you to retest if necessary). D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 73
  • D-Link DSL-2640B | Product Manual - Page 74
    Access the DHCP Leases screen by clicking DHCP under Status. This shows the computers, identified by the hostname and MAC address, that have acquired IP addresses by the DHCP server. The table will also show the time the DHCP lease will expire. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 74
  • D-Link DSL-2640B | Product Manual - Page 75
    information, displaying either ADSL Link Down or ADSL Link Up. WAN Info Route Info The Route Info section displays route information showing the IP addresses of the destination, gateway, and subnet mask as well as other route information. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 75
  • D-Link DSL-2640B | Product Manual - Page 76
    Section 8 - Status Log This is the same screen as seen in the Remotelog section under tools. LAN The LAN section shows received and transmitted packet information for the Ethernet interface. Click on Reset Statistics to renew the information. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 76
  • D-Link DSL-2640B | Product Manual - Page 77
    Section 8 - Status WAN The WAN section shows received and transmitted packet information for the WAN connections that you have set up. Click on Reset Statistics to renew the information. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 77
  • D-Link DSL-2640B | Product Manual - Page 78
    Section 8 - Status ATM The ATM section displays statistical values for your ATM interface as well as for AAL5 and AAL5 VCC. Click on Reset Statistics to reset the values. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 78
  • D-Link DSL-2640B | Product Manual - Page 79
    Section 8 - Status ADSL Information contained in the ADSL screen is useful for troubleshooting and diagnosing connection problems. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 79
  • D-Link DSL-2640B | Product Manual - Page 80
    at the bottom of the ADSL Statistics page, the following pop-up screen will appear allowing you to set the tested time and to begin the test. Click Start to begin the test. When you start the test, click on the Stop button to terminate the test. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 80
  • D-Link DSL-2640B | Product Manual - Page 81
    Section 8 - Status When the test is complete, the following window will display the test results showing the test time, total transferred bits, total error bits and error ratio. Click Exit to close the window. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 81
  • D-Link DSL-2640B | Product Manual - Page 82
    Section 8 - Status Wireless Station Info This page displays the stations (identified by their BSSID) that are associated with your wireless router. Click on Refresh to renew the page for new wireless stations. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 82
  • D-Link DSL-2640B | Product Manual - Page 83
    such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and Windows® XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 83
  • D-Link DSL-2640B | Product Manual - Page 84
    router will go through its reboot process. Wait about 30 seconds to access the router. For information about logging into the router see page 11. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 84
  • D-Link DSL-2640B | Product Manual - Page 85
    , it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 85
  • D-Link DSL-2640B | Product Manual - Page 86
    up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 86
  • D-Link DSL-2640B | Product Manual - Page 87
    recent years that almost everyone is using it, whether it's for home, office, business, D-Link has a wireless solution for it. Home • Gives everyone at home broadband access • Surf the web, multiple computers • No need to dedicate office space D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 87
  • D-Link DSL-2640B | Product Manual - Page 88
    put together a few setup steps and tips to help you through the process of setting up a wireless network. Tips Here are a few things to keep in mind, when you install a wireless network. Centralize your since they operate on same frequency. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 88
  • D-Link DSL-2640B | Product Manual - Page 89
    router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 89
  • D-Link DSL-2640B | Product Manual - Page 90
    your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP xx-xx-xx-xx-xx or xx:xx:xx:xx:xx:xx D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 90
  • D-Link DSL-2640B | Product Manual - Page 91
    LAN IP address of your router (192.168.0.1). Set Primary DNS the same as the LAN IP address of your router (192.168.0.1).The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step 5 Click OK twice to save your settings. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 91
  • D-Link DSL-2640B | Product Manual - Page 92
    answers to technical issues. For customers within the United States: Phone Support: (877) 453-5465 Internet Support: http://support.dlink.com For customers within Canada: Phone Support: (800) 361-5265 Internet Support: http://support.dlink.ca D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 92
  • D-Link DSL-2640B | Product Manual - Page 93
    from D-Link Technical Support at .dlink Link if you use an address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual
  • D-Link DSL-2640B | Product Manual - Page 94
    firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link WARRANTY PERIOD SET FORTH instructions Link office. D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 94
  • D-Link DSL-2640B | Product Manual - Page 95
    Appendix D - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.0 September 26, 2006 D-Link DSL-2640B ADSL2+ 4-Port Router User Manual 95
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95