Danby DWC508BLS Product Manual - Page 4

Installtion Intructions - wine

Get Danby DWC508BLS PDF manuals and user guides View all Danby DWC508BLS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

INSTALLTION INTRUCTIONS TOOLS YOU WILL NEED FOR YOUR SAFETY: While performing installations described in this section, gloves, safety glasses, or goggles should be worn. Safety Glasses Gloves Drill & Hole Saw set Level Flashlight Carpenters Square Measuring Tape PREPARING THE ELECTRICAL REQUIREMENTS: The appliance must be connected to an ENCLOSURE individual, properly grounded electrical outlet, protected by a 15 or 20 ampere circuit breaker or time delay fuse. • It is recommended that you do not install the wine cooler into a corner (i.e. directly beside a wall). This is to allow the door to have a greater then 90° opening swing. A limited door swing may lead to damaging the door gasket. • The rough cabinet opening must be on a level floor area and at least 24" deep by 24" wide. The opening should also have a height of at least 34 3/4". • The electrical oulet may be positioned from within either side of the adjacent cabinetry, or the rear of the shaded area (as shown in Fig E). • If the electrical outlet is located inside the adjacent cabinetry, cut a 1-1/2" diameter hole to admit the power cord. If the cabinet wall is metal, the hole edge must be covered with a bushing or grommet. 34 3/4" From Underside of Countertop to Floor 1 1- /2" dia. hole *if electical outlet is in adjacent cabinetry 24" Min. 2" Electrical Access 6" Cabinets Square and Plumb 24" Fig E 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
Carpenters
Square
Measuring
Tape
Level
Drill & Hole Saw set
Gloves
Safety Glasses
Flashlight
Electrical Access
Cabinets
Square
and
Plumb
34 3/4”
From
Underside
of
Countertop
to Floor
24”
6”
24”
Min.
1-
1
/2” dia. hole
*if electical
outlet is in
adjacent
cabinetry
2”
TOOLS YOU
WILL NEED
FOR YOUR SAFETY:
While performing installations described in
this section, gloves, safety glasses, or goggles
should be worn.
PREPARING THE
ENCLOSURE
ELECTRICAL REQUIREMENTS:
The appliance must be connected to an
individual, properly grounded electrical outlet, protected by a 15 or 20 ampere circuit
breaker or time delay fuse.
•
It is recommended that you do not install the wine cooler into a corner (i.e. directly beside a wall). This is to
allow the door to have a greater then 90° opening swing. A limited door swing may lead to damaging the
door gasket.
•
The rough cabinet opening must be on a level floor area and at least 24” deep by 24” wide.
The opening
should also have a height of at least 34 3/4”.
•
The electrical oulet may be positioned from within either side of the adjacent cabinetry, or the rear of the
shaded area (as shown in
Fig E
).
•
If the electrical outlet is
located inside the adjacent cabinetry, cut a 1-1/2” diameter hole to admit the power
cord. If the cabinet wall is metal, the hole edge must be covered with a bushing or grommet.
INSTALLTION INTRUCTIONS
Fig E
3