Dell C1048P Port Extender Networking C1048P Installation Guide - Page 14

Attaching Mount Brackets to the C1048P

Get Dell C1048P Port Extender PDF manuals and user guides View all Dell C1048P Port Extender manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

CAUTION: Before installing the C1048P in a rack, disconnect all cables (if attached) and remove all self-adhesive pads (if attached) from the underside of the C1048P. CAUTION: If you plan to install multiple C1048P PEs in a rack, mount the C1048s from the bottom up. Make sure that the air flow through the ventilation holes on each C1048P is not obstructed. To install the C1048P in a rack: 1. Align the holes on the right rack-mount bracket with the holes on the right side (facing you) of the C1048P. 2. Secure the bracket (item 3 in Figure 6) to the chassis by tightening the screws (item 2 in Figure 6) provided with the mount bracket. Figure 6. Attaching Mount Brackets to the C1048P 3. Repeat Steps 1 and 2 to attach the left rack-mount bracket on the C1048P. 4. Mount the C1048P into a 48.26 cm (19 inch) rack. Align the holes on each bracket flange with the holes on a rack post. 5. Secure the C1048P to the rack using the rack bolts (provided with the mount brackets) or cage nuts and cage-nut bolts with washers (provided with the rack). Tighten the bolts on the bottom of each bracket flange first; then tighten the bolts on top (item 1 in Figure 7). CAUTION: Make sure that the rack bolts provided with the mounting brackets fit the threaded holes in the rack. 14 Installing the Hardware

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
CAUTION: Before installing the C1048P in a rack, disconnect all cables (if attached) and remove
all self-adhesive pads (if attached) from the underside of the C1048P.
CAUTION: If you plan to install multiple C1048P PEs in a rack, mount the C1048s from the
bottom up. Make sure that the air flow through the ventilation holes on each C1048P is not
obstructed.
To install the C1048P in a rack:
1.
Align the holes on the right rack-mount bracket with the holes on the right side (facing you) of the
C1048P.
2.
Secure the bracket (item 3 in Figure 6) to the chassis by tightening the screws (item 2 in Figure 6)
provided with the mount bracket.
Figure 6. Attaching Mount Brackets to the C1048P
3.
Repeat Steps 1 and 2 to attach the left rack-mount bracket on the C1048P.
4.
Mount the C1048P into a 48.26 cm (19 inch) rack. Align the holes on each bracket flange with the
holes on a rack post.
5.
Secure the C1048P to the rack using the rack bolts (provided with the mount brackets) or cage nuts
and cage-nut bolts with washers (provided with the rack). Tighten the bolts on the bottom of each
bracket flange first; then tighten the bolts on top (item 1 in Figure 7).
CAUTION: Make sure that the rack bolts provided with the mounting brackets fit the
threaded holes in the rack.
14
Installing the Hardware