Dell PowerEdge R910 Information Update - Page 10

Warning, Caution - service manual

Get Dell PowerEdge R910 PDF manuals and user guides View all Dell PowerEdge R910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Removing Memory Modules WARNING: The memory modules are hot to the touch for some time after the system has been powered down. Allow time for the memory modules to cool before handling them. Handle the memory modules by the card edges and avoid touching the components on the memory module. CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. CAUTION: To ensure proper system cooling, memory-module blanks must be installed in any memory socket that is not occupied. Remove memory-module blanks only if you intend to install memory modules in those sockets. 1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 2 Open the system. See "Opening the System" in the Hardware Owner's Manual. 3 Remove the memory risers. See "Removing a Memory Riser" in the Hardware Owner's Manual. 4 Press the tabs in the direction of the arrows and lift the memory module cover. See Figure 2. CAUTION: Handle each memory module only on either card edge, making sure not to touch the middle of the memory module. 5 Press down and out on the ejectors on each end of the socket until the memory module pops out of the socket. 6 Press the four tabs and close the memory module cover. See Figure 2. 10 Information Update

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
10
Information Update
Removing Memory Modules
WARNING:
The memory modules are hot to the touch for some time after the
system has been powered down. Allow time for the memory modules to cool
before handling them. Handle the memory modules by the card edges and avoid
touching the components on the memory module.
CAUTION:
Many repairs may only be done by a certified service technician.
You should only perform troubleshooting and simple repairs as authorized in
your product documentation, or as directed by the online or telephone service
and support team. Damage due to servicing that is not authorized by Dell is not
covered by your warranty. Read and follow the safety instructions that came
with the product.
CAUTION:
To ensure proper system cooling, memory-module blanks must be
installed in any memory socket that is not occupied. Remove memory-module
blanks only if you intend to install memory modules in those sockets.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
Open the system. See "Opening the System" in the
Hardware Owner’s
Manual
.
3
Remove the memory risers. See "Removing a Memory Riser" in the
Hardware Owner’s Manual
.
4
Press the tabs in the direction of the arrows and lift the memory
module cover. See Figure 2.
CAUTION:
Handle each memory module only on either card edge, making sure
not to touch the middle of the memory module.
5
Press down and out on the ejectors on each end of the socket until the
memory module pops out of the socket.
6
Press the four tabs and close the memory module cover. See Figure 2.