Dell PowerStore 9000T EMC PowerStore Hardware Information Guide - Page 10

About 4-port cards, Table 4. Embedded module component locations

Get Dell PowerStore 9000T PDF manuals and user guides View all Dell PowerStore 9000T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

The first two ports of the 4-port card on the embedded module connect to a 10GbE/25GbE Ethernet switch. NOTE: Both nodes must have the same type of embedded modules in the same slots. The embedded module contains the following components: ● One 4-port card ● One non-maskable interrupt (NMI) button ● Two mini-SAS HD back-end ports ● Two RJ-45 LAN connectors ○ System management port ( ) ○ Service port ( ) ● One USB port ● One mini-serial port (unused) ● One DB9 serial port (unused) NOTE: The following figure shows the location of these components on the embedded module in node A. The locations of the components in node B are mirrored. Figure 6. Embedded module rear view with component locations Table 4. Embedded module component locations Location Description 4-port card Mini serial port (unused) Mini-SAS HD back-end ports DB9 serial port (service) 5 RJ-45 LAN connector - service port 6 RJ 45 LAN connector - system management port. Only used on PowerStore T model. Not used on PowerStore X model. 7 Non-maskable interrupt (NMI) button 8 USB port About 4-port cards The 4-port card is an optional component located within the embedded module. There are two supported 4-port cards: the 4port 25GbE SFP based embedded module and the 4-port 10GBaseT embedded module. The 4-port 25GbE SFP based embedded module supports 1GbE SFP to RJ45, 10GbE or 25GbE SFP28, 25GbE passive TwinAx, and 10GbE active or passive TwinAx. Depending on the installed SFP or TwinAx cable, the following speeds are supported: 1GbE, 10GbE, and 25GbE. The ports may be configured individually with TwinAx or any of the supported SFPs. 10 Base enclosure component descriptions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
The first two ports of the 4-port card on the embedded module connect to a 10GbE/25GbE Ethernet switch.
NOTE:
Both nodes must have the same type of embedded modules in the same slots.
The embedded module contains the following components:
●
One 4-port card
●
One non-maskable interrupt (NMI) button
●
Two mini-SAS HD back-end ports
●
Two RJ-45 LAN connectors
○
System management port (
)
○
Service port (
)
●
One USB port
●
One mini-serial port (unused)
●
One DB9 serial port (unused)
NOTE:
The following figure shows the location of these components on the embedded module in node A. The locations of
the components in node B are mirrored.
Figure 6. Embedded module rear view with component locations
Table 4. Embedded module component locations
Location
Description
4-port card
Mini serial port (unused)
Mini-SAS HD back-end ports
DB9 serial port (service)
5
RJ-45 LAN connector - service port
6
RJ 45 LAN connector - system management port. Only used on PowerStore T
model. Not used on PowerStore X model.
7
Non-maskable interrupt (NMI) button
8
USB port
About 4-port cards
The 4-port card is an optional component located within the embedded module. There are two supported 4-port cards: the 4-
port 25GbE SFP based embedded module and the 4-port 10GBaseT embedded module.
The 4-port 25GbE SFP based embedded module supports 1GbE SFP to RJ45, 10GbE or 25GbE SFP28, 25GbE passive TwinAx,
and 10GbE active or passive TwinAx. Depending on the installed SFP or TwinAx cable, the following speeds are supported: 1GbE,
10GbE, and 25GbE. The ports may be configured individually with TwinAx or any of the supported SFPs.
10
Base enclosure component descriptions