Dell PowerStore 9000T EMC PowerStore Hardware Information Guide - Page 16

U, 25-drive expansion enclosure rear view, 25-drive expansion enclosure link control card

Get Dell PowerStore 9000T PDF manuals and user guides View all Dell PowerStore 9000T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Table 9. 2U, 25-drive expansion enclosure and drive status LEDs (continued) LED Location Color State Description - Off Powered down Drive fault 4 Amber On - Off Fault No fault Drive power and activity 5 Blue On Blinking Powering up and powered up Drive activity 2U, 25-drive expansion enclosure rear view The rear of the 2U, 25-drive expansion enclosure includes the following components: ● Two 12-Gb/s SAS link control cards (LCC); A ( 4 ) and B ( 2 ) ● Two power supply and cooling modules; A ( 3 ) and B ( 1 ) 1 2 3 x4 x4 01 # B 0 1 A x4 x4 # 4 Figure 11. 2U, 25-drive expansion enclosure rear component locations 2U, 25-drive expansion enclosure link control card Link control card functions and features The link control card (LCC) supports, controls, and monitors the expansion enclosure, and is the primary interconnect management element. Each LCC includes connectors for input and output to downstream devices. The LCCs in an expansion enclosure connects to the node and other expansion enclosures. The cables connect the LCCs in a system in a daisy-chain topology. Internally, each expansion enclosure LCC uses protocols to emulate a loop. The LCC connects to the drives in its enclosure in a point-to-point fashion through an internal switch. The LCC independently receives and electrically terminates incoming signals. For traffic from the node, the LCC switch passes the signal from the input port to the drive being accessed. The switch then forwards the drive output signal to the port. Each LCC independently monitors the environmental status of the entire enclosure, using a microcomputer-controlled monitor program. The monitor communicates the status to the storage processor, which polls expansion enclosure status. LCC firmware also controls the SAS and drive-module status LEDs. Each LCC includes an enclosure ID display. 12-Gb/s LCC ports, LEDs, and connectors Each 2U, 25 expansion enclosure LCC shows the following ports, LEDs, and connectors: 16 Expansion enclosure component descriptions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
Table 9. 2U, 25-drive expansion enclosure and drive status LEDs (continued)
LED
Location
Color
State
Description
—
Off
Powered down
Drive fault
4
Amber
On
Fault
—
Off
No fault
Drive power and activity
5
Blue
On
Powering up and powered up
Blinking
Drive activity
2U, 25-drive expansion enclosure rear view
The rear of the 2U, 25-drive expansion enclosure includes the following components:
●
Two 12-Gb/s SAS link control cards (LCC); A (
4
) and B (
2
)
●
Two power supply and cooling modules; A (
3
) and B (
1
)
B
A
0
1
#
#
0
1
x4
x4
x4
x4
1
2
3
4
Figure 11. 2U, 25-drive expansion enclosure rear component locations
2U, 25-drive expansion enclosure link control card
Link control card functions and features
The link control card (LCC) supports, controls, and monitors the expansion enclosure, and is the primary interconnect
management element. Each LCC includes connectors for input and output to downstream devices.
The LCCs in an expansion enclosure connects to the node and other expansion enclosures. The cables connect the LCCs in a
system in a daisy-chain topology.
Internally, each expansion enclosure LCC uses protocols to emulate a loop. The LCC connects to the drives in its enclosure in a
point-to-point fashion through an internal switch. The LCC independently receives and electrically terminates incoming signals.
For traffic from the node, the LCC switch passes the signal from the input port to the drive being accessed. The switch then
forwards the drive output signal to the port.
Each LCC independently monitors the environmental status of the entire enclosure, using a microcomputer-controlled monitor
program. The monitor communicates the status to the storage processor, which polls expansion enclosure status. LCC firmware
also controls the SAS and drive-module status LEDs.
Each LCC includes an enclosure ID display.
12-Gb/s LCC ports, LEDs, and connectors
Each 2U, 25 expansion enclosure LCC shows the following ports, LEDs, and connectors:
16
Expansion enclosure component descriptions