Dell PowerVault 210S Dell PowerVault 20xS Storage Systems Enclosure Services - Page 6

NOTE: HP OpenView Network Node Manager Special Edition NNM SE 1.4 - configuration

Get Dell PowerVault 210S PDF manuals and user guides View all Dell PowerVault 210S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

noncluster operation (default configuration) cluster operation (forced joined mode) two-pin jumper (FORCED JOINED JP8) If you want to configure the enclosure services expander modules from a cluster operation to a noncluster operation, perform the following procedure on each module: 1. Remove the enclosure services expander module. See "Replacing the Enclosure Services Expander Module" found later in this document where removing the module is described. 2. Locate the two-pin jumper labeled "FORCED JOINED JP8" on the enclosure services expander module (see Figure 1-1). 3. Move the jumper plug to connect only one pin of the FORCED JOINED JP8 jumper. 4. Install the two enclosure services expander modules into the PowerVault 20xS storage system. See "Installing the Enclosure Services Expander Module" found later in this document. NOTE: HP OpenView Network Node Manager Special Edition (NNM SE) 1.4 With Dell OpenManage HIP 3.4 contains the backplane configuration feature that is used to configure the enclosure services expander module for cluster operation through software. However, this feature does not function properly. This problem will be addressed in a future release of HP OpenView NNM SE x.x With Dell OpenManage HIP x.x. 1-4 Dell PowerVault 20xS Storage Systems Enclosure Services Expander Module Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
1-4
Dell PowerVault 20xS Storage Systems Enclosure Services Expander Module Installation
±²³´µ¶·¸¹¸º··»¼½¾¿À´µ¶·Á¶µÂ²½¶À·»ÃÄżƶµ·Ç¿Æ´¾¶
If you want to configure the enclosure services expander modules from a cluster
operation to a noncluster operation, perform the following procedure on each module:
1.
Remove the enclosure services expander module.
See
“
Replacing the Enclosure Services Expander Module
”
found later in this
document where removing the module is described.
2.
Locate the two-pin jumper labeled
“
FORCED JOINED JP8
”
on the enclosure
services expander module (see Figure 1-1).
3.
Move the jumper plug to connect only one pin of the FORCED JOINED JP8
jumper.
4.
Install the two enclosure services expander modules into the PowerVault 20
x
S
storage system.
See
“
Installing the Enclosure Services Expander Module
”
found later in this
document.
NOTE: HP OpenView Network Node Manager Special Edition (NNM SE) 1.4 With
Dell OpenManage HIP 3.4 contains the backplane configuration feature that is used
to configure the enclosure services expander module for cluster operation through
software. However, this feature does not function properly. This problem will be
addressed in a future release of HP OpenView NNM SE x.x With Dell OpenManage
HIP x.x.
cluster operation
(forced joined mode)
noncluster operation
(default configuration)
two-pin jumper
(FORCED JOINED JP8)