Dewalt D21002 Instruction Manual

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

D21002, D21008, D21009

3/8" (10mm) V.S.R. Drill

Perceuse de 10 mm (3/8 po) à régulateur de vitesse et inverseur

de marche

Taladro de 10mm (3/8") V.V.R.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA.

ADVERTENCIA:

LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D

E

WALT TOOL,

CALL US TOLL FREE AT:

1-800-4-D

E

WALT (1-800-433-9258)

GENERAL SAFETY INSTRUCTIONS FOR ALL TOOLS

WARNING! Read and understand all instructions.

Failure to follow all instruc-

tions listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

•

Keep your work area clean and well lit

. Cluttered benches and dark areas invite accidents.

•

Do not operate power tools in explosive atmospheres, such as in the presence of flam-

mable liquids, gases, or dust.

Power tools create sparks which may ignite the dust or

fumes.

•

Keep bystanders, children, and visitors away while operating a power tool.

Distractions

can cause you to lose control.

ELECTRICAL SAFETY

•

Grounded tools must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or

modify the plug in any way. Do not use any adaptor plugs. Check with a qualified elec-

trician if you are in doubt as to whether the outlet is properly grounded.

If the tools

should electrically malfunction or break down, grounding provides a low resistance path to

carry electricity away from the user.

•

Double insulated tools are equipped with a polarized plug (one blade is wider than the

other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully

in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to

install a polarized outlet. Do not change the plug in any way.

Double insulation

elim-

inates the need for the three wire grounded power cord and grounded power supply system.

•

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your body is grounded.

•

Don’t expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock.

•

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged

cords immediately.

Damaged cords increase the risk of electric shock.

•

When operating a power tool outside, use an outdoor extension cord marked “W-A”

or “W.”

These cords are rated for outdoor use and reduce the risk of electric shock. When

using an extension cord, be sure to use one heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-

ber, the heavier the cord.

Minimum Gage for Cord Sets

Volts

Total Length of Cord in Feet

120V

0-25

26-50

51-100

101-150

240V

0-50

51-100

101-200

201-300

Ampere Rating

More

Not more

AWG

Than

Than

0

-

6

18

16

16

14

6

-

10

18

16

14

12

10 -

12

16

16

14

12

12 -

16

14

12

Not Recommended

PERSONAL SAFETY

•

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may result in serious personal injury,

•

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,

clothing , and gloves away from moving parts.

Loose clothes, jewelry, or long hair can be

caught in moving parts. Air vents often cover moving parts and should also be avoided.

•

Avoid accidental starting. Be sure switch is off before plugging in.

Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

•

Remove adjusting keys or wrenches before turning the tool on.

A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

•

Do not overreach. Keep proper footing and balance at all times.

Proper footing and bal-

ance enables better control of the tool in unexpected situations.

•

Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

•

Use clamps or other practical way to secure and support the workpiece to a stable

platform.

Holding the work by hand or against your body is unstable and may lead to loss of

control.

•

Do not force tool. Use the correct tool for your application.

The correct tool will do the

job better and safer at the rate for which it is designed.

•

Do not use tool if switch does not turn it on or off.

Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

•

Disconnect the plug from the power source before making any adjustments, changing

accessories, or storing the tool.

Such preventative safety measures reduce the risk of starting

the tool accidentally.

•

Store idle tools out of reach of children and other untrained persons.

Tools are danger-

ous in the hands of untrained users.

•

Maintain tools with care. Keep cutting tools sharp and clean.

Properly maintained tools,

with sharp cutting edges are less likely to bind and are easier to control.

•

Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced

before using

. Many accidents are caused by poorly maintained tools.

•

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

SERVICE

•

Tool service must be performed only by qualified repair personnel.

Service or mainte-

nance performed by unqualified personnel could result in a risk of injury.

•

When servicing a tool, use only identical replacement parts. Follow instructions in the

Maintenance section of this manual

. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of electric shock or injury.

Additional Specific Safety Instructions for Drills

•

Hold tool by insulated gripping surfaces when performing an operation where the cut-

ting tools may contact hidden wiring or its own cord.

Contact with a “live” wire will make

exposed metal parts of the tool “live” and shock the operator.

•

Wear safety goggles or other eye protection.

Hammering and drilling operations cause

chips to fly. Flying particles can cause permanent eye damage.

•

Keep handles dry, clean, and free from oil and grease.

This will enable better control of the tool.

C

AUTION: DO NOT TOUCH ANY METAL PARTS OF THE TOOL when drilling or driving into

walls, floors or areas where live electrical wires may be encountered

. Hold the tool only by insulated

grasping surfaces to prevent electric shock if you drill

or drive into a

live wire.

CAUTION: Wear appropriate hearing protection during use.

Under some conditions and

duration of use, noise from this product may contribute to hearing loss.

WARNING

: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

•

lead from lead-based paints,

•

crystalline silica from bricks and cement and other masonry products, and

•

arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with approved

safety equipment, such as those dust masks that are specially designed to filter out microscopic

particles.

•

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water.

Allowing dust to get into your mouth, eyes, or lay on the skin may pro-

mote absorption of harmful chemicals.

WARNING:

Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

•

The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V

............

volts

A

................

amperes

Hz

..........

hertz

W

................

watts

min

..........

minutes

................

alternating current

........

direct current

n

o

................

no load speed

............

Class II Construction

…/min

........

revolutions or reciprocation per minute

..........

earthing terminal

..............

safety alert symbol

Motor Brushes

D

E

WALT uses an advanced brush system which automatically stops the drill when the brushes

wear out. This prevents serious damage to the motor.

Switches (Figure 1)

To start the drill, depress the trigger switch; to stop the drill, release the trigger.

A variable speed trigger switch (A) permits speed control—the farther the trigger is depressed,

the higher the speed of the drill.

NOTE:

Use lower speeds for starting holes without a center punch, drilling in metal or plastics,

driving screws or drilling ceramics. Higher speeds are better for drilling wood and composition

boards and using abrasive and polishing accessories.

The reversing lever (B) is used for withdrawing bits from tight holes and removing screws. It is

located above the trigger switch. To reverse the motor, release the trigger switch FIRST and then

push the lever to the right. After any reversing operations, return lever to forward position.

OPERATION

Drilling

1. Always unplug the drill when attaching or changing bits or accessories.

2. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole

saws. For METAL, use high speed steel twist drill bits or hole saws. For MASONRY, such

as brick, cement, cinder block, etc., use carbide-tipped bits.

3. Be sure the material to be drilled is anchored or clamped firmly. When drilling thin material,

use a wood “back-up” block to prevent damage to the material.

4. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill bit-

ing, but do not push hard enough to stall the motor or deflect the bit.

5. Hold tool firmly to control the twisting action of the drill.

6. Overloading and improper use may cause the drill to stall. If the drill stalls, release the trigger

immediately remove drill bit from work, and determine cause of stalling. Do not click the

trigger off and on in an attempt to start the drill — this can damage the drill.

7. To minimize stalling or breaking through the material, reduce the pressure on drill and ease

the bit through the last fractional part of the hole.

8. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent

jamming.

D

E

WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

(DEC04) Form No. 626493-00

D21002, D21008, D21009

Copyright © 2002, 2004 D

E

WALT

The following are trademarks for one or more D

E

WALT power tools: the yellow and black color

scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box con-

figuration; and the array of lozenge-shaped humps on the surface of the tool.

Questions? See us on the World Wide Web at www.dewalt.com

Dewalt D21002 Instruction Manual

Dewalt D21002 Manual

Dewalt D21002 manual content summary: